压力容器、储气罐、压力容器焊接专业英语

标签：专业英语 weld name 压力容器 material heat design 储气罐 quality

分类 classification	英文 english	中文 chinese
defect	approval of defect in material	材料中缺陷的认可
defect	arc crater	弧坑
defect	penetration	毛边
defect		不整齐的飞边修整
defect	crack	裂缝
defect	crack-like inperfection	裂纹状缺陷
defect	cutting chip	切屑
defect	damage	损伤
defect	defect	缺陷
defect	forging	锻件中的缺陷
defect	defect in weld	焊缝中的缺陷
defect	defect in welded vessel	焊接容器中的缺陷
defect	defective brazing	有缺陷的钎焊
defect	deformation	变形
defect	dings	勾缝
defect	distortion	变形
defect	grease	油脂
defect	incomplete filled groove	未填满
defect	incomplete fusion	未熔合
defect	incomplete penetration	未焊透
defect	lamination	分层缺陷
defect	loose inside-diameter bead	松散开的内表面焊道
defect	mechanical impurity	机械杂质
defect	overlap	焊瘤
defect	pore	气孔
defect	porosity	多孔性
defect	Radiation embrittlement	辐射脆化
defect	repair of defect	缺陷的修补
defect	scab	痂
defect	scratch	表面擦伤
defect	slag inclusion	夹渣
defect	sliver	毛刺
defect	spatter	飞溅
defect	steel die stamp	钢模痕迹
defect	stop mark	制动伤痕
defect	straigntener mark	矫直划痕
defect	stress corrosion cracking	应力腐蚀裂缝
defect	surface roughness	表面粗糙
defect	tube reducer ripple	管子减径皱纹
defect	undercut	咬边
defect	weld spatter	焊接飞溅
design	absolute pressure	绝对压力
design	additional thickness	厚度附加量
design	allowable	许用的
design	allowable stress	许用应力
design	allowable working pressure	许用工作压力
design	allowance	裕量
design	allowance for abrasion	磨损裕量
design	allowance for corrosion	腐蚀裕量
design	allowance for erosion	侵蚀裕量
design	analysis	分析
design	applied linings, tightness	应用衬里密封性
design	area replacement method	等面积补强
design	basic seismic acceleration	基本地震加速度
design	basic wind pressure	基本风压
design	basis for establishing	确定的基础
design	bolt land	螺栓载荷
design	bolt stress	螺栓应力
design	bolted design	螺柱设计
design	calculate	计算
design	calculated thickness	计算厚度
design	capacity	容量
design	category	类别
design	chart	图表
design	check	校核
design	circumferential /hoop stress	环向应力
design	circumferential efficiency	环缝系数
design	circumferential joint	环向连接
design	computation	计算
design	computation of opening	开孔计算
design	computed working pressure from hydrostatic test	由水压试验计算的工作压力
design	conversion	换算
design	corrosion allowance	腐蚀裕量
design	corrosion rate	腐蚀速率
design	curvature	曲率
design	design	设计
design	Design by analysis	分析设计
design	design by rules	常规设计
design	design pressure	设计压力
design	designed life	使用寿命
design	Dynamic load	动载荷
design	earthquake load	地震载荷
design	effective gasket width	有效垫片宽度
design	efficiency	系数
design	elasticity modulu	弹性模量
design	empty weight	容器净重
design	erosion allowance	侵蚀裕量
design	factor	系数
design	fixed	固定的
design	flammable	易然的
design	flange moment	法兰力矩
design	flange stresse	法兰应力
design	fluid	流体（介质）
design	fluid property	介质特性
design	for drainage	用于排放
design	for gas and liquid	用于气体和液体
design	for screw stay	用于螺丝固定
design	for trepanning plug section	用于穿孔螺塞部分
design	for unfired steam boiler	对非直接火蒸气锅炉
design	for vessel under external pressure	用于外压容器
design	form of specification	技术条件
design	hard conversion	硬性换算
design	heat transfer surface	传热面
design	hoop stress	环向应力
design	horizontal	卧式
design	integral reinforcement	整体补强
design	joint efficiency	接头系数
design	less than 6 mm thickness	厚度小6mm
design	lethal gases or liquids	致命的气体或液体
design	ligament efficiency	孔带系数
design	limit	极限
design	limit of reinforcement	补强范围
design	limiting stresse	极限应力
design	liquid relief	液体泄放
design	loading	载荷
design	localized thin area	局部薄壁区
design	low stress	低应力
design	low-temperature operation	低温操作
design	low-temperature vessel	低温容器
design	main parameter	主要参数
design	maximum allowable efficiency	最大许用系数
design	maximum service temperature	最高使用温度
design	membrane stress	薄膜应力
design	metal temperature	金属温度
design	minimum requirement	最低要求
design	minimum thickness	最小厚度
design	minimum thickness of neck	缩颈的最小厚度
design	minimum thickness of plate	板材的最小厚度控制
design	minimum vessel diameter requiring	所需最小容器直径
design	modulus of elasticity	弹性模量
design	molecular weight of gas and vapor	气体和蒸汽的分子量
design	multichamber vessel design	多承压室容器的设计
design	natural frequency	固有频率
design	nominal pressure	工称压力
design	nominal thickness	名义厚度
design	not requiring additional reinforcement	不需要附加补强
design	obround design	长圆形设计
design	operating or working	操作或工作
design	operating temperature	操作温度
design	operation pressure	工作压力
design	operation/service temperature	工作温度
design	overpressure limit for vessel	容器的超压极限
design	peak stress	峰值应力
design	pressure	压力
design	pressure setting	压力设定
design	pressure-temperatures limitations	压力-温度界限
design	primary stress	一次应力
design	primary stress	主应力
design	produce form of specification	产品技术条件
design	radial stress	径向应力
design	rectangular design	矩形设计
design	requiring additional reinforcement	需要附加补强
design	risk assessment	风险分析
design	safety assessment	安全评定
design	safety factor	安全系数
design	scope	适用范围
design	secondary stress	次要应力
design	secondary stress	二次应力
design	secondary stress	二次应力
design	seismic intensity	地震烈度
design	separate reinforcement	单独补强
design	shakedown	安定
design	shapes permissible	许用形式
design	soft conversion	软性换算
design	spherical radius factor k1	球半径系数K1
design	stiffness	刚性
design	stress analysis	应力分析
design	stress concentration	应力集中
design	stress corrosion	应力腐蚀
design	stress value	应力值
design	supplementary design formula	补充设计公式
design	supplementary loading	附加载荷
design	termination point of a vessel	容器的界限点
design	thermal stress	热应力
design	total volume	全容积
design	toxicity	毒性
design	unreinforced	非补强的
design	vertical	立式
design	vessel classification	容器类别
design	vessels whose strength cannot be calculated	不能由计算求得强度的容器
design	volume	容积
design	wind load	风载荷
design	working pressure	工作压力
head	concave	凹面
head	conical	锥形
head	conical head	锥形封头
head	convex	凸面
head	design of head	封头设计
head	dished head	碟形封头
head	ellipsoidal	椭圆形
head	ellipsoidal head	椭圆封头
head	flat head	平封头
head	flat spot on formed head	成型封头上的平坦部分
head	forged heads	锻造封头
head	formed	成型的
head	formed head	成型封头
head	forming	成型
head	head	封头
head	head and shell opening	封头及壳体开孔
head	head flange (skirt) length	封头翻边(直边)长度
head	head joint	封头接头
head	head opening	封头开孔
head	heads into shell	封头接入壳体
head	hemispherical	半球形
head	hemispherical head	半球形封头
head	high pressure vessel	高压封头
head	in flat head	在平板封头上
head	integral cast iron dished head	整体铸铁碟形封头
head	segment of head	封头凸形部分
head	skirts length on head	封头上直边的长度
head	spherical	球形
head	spherically dished	球状碟形
head	torispherical head	碟形封头
head	unstayed flat head and cover	无支撑平封头和盖板
heat exchanger	expansion joint	膨胀节
heat exchanger	finned tubes	翅片管
heat exchanger	fixed tube sheet heat exchanger	固定管板式换热器
heat exchanger	floating head heat exchanger	浮头式换热器
heat exchanger	integrally finned tube	整体翅片管
heat exchanger	plate-fin heat wxchanger	板翅式换热器
heat exchanger	shell and tube heat exchanger	管壳式换热器
heat exchanger	shell side	壳程
heat exchanger	spacer	定距管
heat exchanger	tube	管子
heat exchanger	tube fin heat exchanger	管翅式换热器
heat exchanger	tube sheet	管板
heat exchanger	tube sheet extended as a flange	管板兼作法兰
heat exchanger	tube side	管程
heat exchanger	tube-to-tubesheet	管子对管板
heat exchanger	tube-to-tubesheet joint	管子与管板的连接
heat exchanger	tubular heat exchanger	管式换热器
heat exchanger	u-type heat exchanger	U型管式换热器
heat exhchanger	classification of heat exchanger	换热器分类
heat exhchanger	expanded	胀接
heat exhchanger	expanded connection	胀接连接
heat treatment	after postweld heat treating	焊后热处理
Heat treatment	anneal	退火
heat treatment	cooling	冷却
heat treatment	cooling after	随后的冷却
heat treatment	enhanced by heat treatment	经热处理后提高××
heat treatment	ferritic steel vessel with tensile properties enhanced by heat treatment	经热处理后提高抗拉性能的铁素体钢容器
heat treatment	furnace	炉子
heat treatment	furnace temperature	炉温
heat treatment	furnaces for heat treating	热处理炉
heat treatment	heat exchanger	热交换器
heat treatment	heat transfer equipment	传热设备
heat treatment	heat treatment	热处理
heat treatment	heat treatment verification test	热处理验证试验
heat treatment	holding temperature	保温温度
heat treatment	holding time	保温时间
heat treatment	local	局部
heat treatment	local postweld heat treatment	局部焊后热处理
Heat treatment	normalize	正火
heat treatment	postheat treatment	后热处理
heat treatment	postweld heat treatment	焊后热处理
heat treatment	postweld heat treatment requirement	焊后热处理要求
heat treatment	preheat	预热
heat treatment	preheating	预热
heat treatment	quench	淬火
heat treatment	recommended temperature range for heat treatment	推荐的热处理温度范围
heat treatment	solution anneal	固熔退火
heat treatment	stress relief	消应力
heat treatment	temper	回火
heat treatment	temperature	温度
heat treatment	temperature control of	温度控制
heat treatment	temperature free movement under	在温度下活动不受约束
heat treatment	temperature range	温度范围
heat treatment	temperatures for postweld head treatment	焊后热处理温度
heat treatment	tempering	回火
heat treatment	test specimen	试样的热处理
heat treatment	thermal treatment	热处理
heat treatment	thermocouple	热电偶
material	approval of new material	新材料的批准
material	austenitic stainless steel	奥氏体不锈钢
material	carbon and low-alloy steel	碳钢和低合金钢
material	carbon content	含碳量
material	carbon in material for welding	焊接用材料中的碳
material	carbon steel	碳钢
material	cast ductile iron	可锻铸铁
material	cast iron	铸铁
material	casting	铸件
material	certification of material	材料证明书
material	chemical composition	化学成份
material	chip marks on integrally forged vessel	整体锻造容器上的缺口标志
material	clad material	覆层材料
material	clad plate	复合板
material	combination of different material	不同材料组合
material	cut	切割
material	cutting plate	板材切割
material	deterioration of material	材质劣化
material	duplex steel	双相钢
material	ferrous	铁基
material	forged	锻造的
material	forged part	锻造部件
material	froging	锻件
material	high-alloy steel	高合金钢
material	identification	识别
material	identification marker	识别标志
material	low alloy steel	低合金钢
material	low alloy steel vessel	低合金钢容器
material	marking transfer after cutting	在切割以后标记的转移
material	material	材料
material	materials having different coefficients of expansion	膨胀系数不同的材料
material	metal	金属
material	metal removal from	从××去除金属
material	new material	新材料
material	non-ferrous	非铁基
material	nonferrous metal	非铁金属
material	non-metal	非金属
material	nonpressure part	非受压元件
material	plate	板材
material	plate edge	板边缘
material	plate of unequal thickness	不等厚板
material	preparation of plate	板材的制备
material	pressure part	受压件
material	rod, bar and shape	杆,棒和型材
material	rolled part	轧制件
material	sheet of material for nozzle	管口材料表
material	shell plate	筒体板
material	specification for material	材料标准
material	stainless steel	不锈钢
material	stenciling plate for identification	在板材上打印标志
material	structural carbon steel	结构碳钢
material	thin plate marking	薄板标志
material	to be visible on plate	在板上可见
material	transfering marking on plate	板上标志的移植
material	type of steel permissible	容许的钢材类型
material	unidentified	未识别的
material	unidentified material	未识别的材料
mechanical	bending stress	弯曲应力
mechanical and chemical	across	横向
mechanical and chemical	as welded	焊态
mechanical and chemical	back bend	背弯
mechanical and chemical	bend test	弯曲试验
mechanical and chemical	brittle fracture	脆性断裂
mechanical and chemical	composition	成分
mechanical and chemical	corrosion resistant	抗腐蚀
mechanical and chemical	corrosion resistant lining	防腐蚀衬里
mechanical and chemical	corrosion-resistant material	防腐材料
mechanical and chemical	coupon	试块
mechanical and chemical	drop weight test	落锤试验
mechanical and chemical	ductility	韧性
mechanical and chemical	elongation	延伸率
mechanical and chemical	etch test	侵蚀试验
mechanical and chemical	etching plug taken	解剖样的侵蚀
mechanical and chemical	excessive local deformation	过度局部弯形
mechanical and chemical	face bend	面弯
mechanical and chemical	hardness	硬度
mechanical and chemical	impact load	冲击载荷
mechanical and chemical	impact specimen	冲击试样
mechanical and chemical	impact test	冲击试验
mechanical and chemical	impact test requirement	冲击试验要求
mechanical and chemical	notch ductility test	缺口韧性试验
mechanical and chemical	reduction of area	断面收缩率
mechanical and chemical	rupture elongation	断后伸长率
mechanical and chemical	sample	样品（试件）
mechanical and chemical	sectioned speciment	截面试样
mechanical and chemical	side bend	侧弯
mechanical and chemical	sigma-phase formation	Σ相的形成
mechanical and chemical	solution for examination for material	检验材料的溶液
mechanical and chemical	specimen	试样
mechanical and chemical	strength	强度
mechanical and chemical	tensile strength	抗拉强度
mechanical and chemical	tensile test	拉伸试验
mechanical and chemical	test coupon	试块
mechanical and chemical	test specimen	试样
mechanical and chemical	testing of material	材料试验
mechanical and chemical	yield strength	屈服强度
mechanical and chemical	yielding	屈服
name 1	ancillary /auxiliary equipment	辅助设备
name 1	clad vessel	覆层容器
name 1	enameled vessel	搪玻璃容器
name 1	evaporator	蒸发器
name 1	external pressure vessel	外压容器
name 1	fired process tubular heater	直接火管式加热炉
name 1	forged vessel	锻造容器
name 1	galvanized vessel	镀锌容器
name 1	heat-exchange vessel	换热压力容器
name 1	in vessels subjected to external pressure	在承受外压的容器
name 1	jacketed vessel	夹套容器
name 1	Layered vessel	多层容器
name 1	monobloc vessel	单层容器
name 1	multichamber vessel	多受压室容器
name 1	multiple duplicate vessel	多个相同的容器
name 1	multiple pressure vessel	多层压力容器
name 1	noncircular vessel	非圆形容器
name 1	over ground horizontal storage tank	地面卧式储罐
name 1	plate column	板式塔
name 1	pressure relieving device	泄压装置
name 1	pressure vessel	压力容器
name 1	process equipment	过程设备
name 1	reaction vessel	反应压力容器
name 1	separation vessel	分离压力容器
name 1	sphere	球形储罐
name 1	spherical tank	球罐
name 1	steam generating vessel	蒸汽发生容器
name 1	storage tank	储罐
name 1	storage vessel	储存容器
name 1	super-high pressure vessel	超高压容器
name 1	tank	罐，桶，槽
name 1	thermal buffer	热缓冲器
name 1	thin-walled vessel	薄壁容器
name 1	tubular reactor	管式反应器
name 1	unfired steam boiler	非直接火蒸汽锅炉
name 1	vessel	容器
name 2	acting as partial shell stiffeners	作为部分壳体加强圈
name 2	anchor bolt	地脚螺栓
name 2	arranged-type packing	规整填料
name 2	attachment	附件
name 2	backing strip	垫板
name 2	baffle plate	挡板
name 2	baffle plate	折流板
name 2	bars	棒
name 2	base plate	基础模板
name 2	bellow expansion joint	波纹管膨胀节
name 2	blind flange	盲板法兰
name 2	bolt	螺栓
name 2	butt strap	对接盖板
name 2	channel	管箱
name 2	cladding and applied lining	覆层及衬里
name 2	clamp	卡箍
name 2	closure	封闭件
name 2	coil tube	盘管
name 2	concentric wrapped shell	层板包扎筒体
name 2	conical sections	圆锥截面
name 2	conical shell	锥壳
name 2	connection	接管（管接头），连接接头，连接件
name 2	corrugated shell	波纹形壳体
name 2	corrugating paper	波纹板
name 2	cover plate	盖板
name 2	cylindrical shell	柱状壳体
name 2	discharge pipe	排放管
name 2	earth lug	接地板
name 2	elbow	弯头
name 2	end	端部
name 2	end of shell plate and butt strap	壳体板和对接搭板端
name 2	fitting	配件
name 2	flange	法兰
name 2	flat bar	扁钢
name 2	forming end	成型端
name 2	gasket	垫片
name 2	impingement baffle	防冲板
name 2	insulation support	保温支撑
name 2	internal shell	内衬筒
name 2	internal structure	内部构件
name 2	jacket	夹套
name 2	jbckscrew	顶丝
name 2	ladder, platform	梯子、平台
name 2	leg	支腿
name 2	lining	衬里
name 2	loose type flange with stub end	翻边法兰
name 2	lug	耳座
name 2	lug and fitting	支耳和配件
name 2	lug support	耳式支座
name 2	male and female facing flange	凹凸面法兰
name 2	manhole, handhole	人孔，手孔
name 2	miscellaneous pressure part	其它受压件
name 2	miscellaneous pressure part	其它受压件
name 2	nameplate	铭牌
name 2	nipple	管嘴
name 2	nozzle	接管,管接头
name 2	nozzle and fitting	接管和配件
name 2	nozzle opening	接管开孔
name 2	nut	螺母
name 2	nut and washer	螺母和垫圈
name 2	o ring	O型环
name 2	on manholes and handhole	在人孔和手孔上的
name 2	pad	凸缘
name 2	pass divider	分层隔板
name 2	pin dowel	定位销
name 2	pipe	公称管
name 2	pipe and nozzle neck to vessel wall	在器壁上的管子和接管颈
name 2	pipe fitting	管子配件
name 2	pipe used for shell	用作壳体的管子
name 2	piping external to vessel	容器外的管子
name 2	plug	螺塞
name 2	pump	泵
name 2	quick-actuating closure	快开盖
name 2	rear end head	后端管箱
name 2	reducer	异径管件
name 2	reducer concentric	同心异径管
name 2	reducer eccentric	偏心异径管
name 2	reducer section	变径段
name 2	reducing elbow	异径弯头
name 2	reducing tee	异径三通
name 2	reinforcement for adjacent opening	邻近开孔的补强
name 2	reinforcement for opening	开孔补强
name 2	reinforcing nozzle	补强管
name 2	reinforcing plate	补强板
name 2	reinforcing ring	补强圈
name 2	rib plate	筋板
name 2	ring support	圈式支座
name 2	saddle support	鞍式支座
name 2	screw, holes for	螺孔
name 2	sealing device	密封装置
name 2	shell	壳体
name 2	shell of revolution	回转壳体
name 2	skirt support	裙座
name 2	slip-on flange	平焊法兰
name 2	spiral gasket	缠绕垫
name 2	spring	弹簧
name 2	spring loaded	受载弹簧
name 2	spring washer	弹簧垫圈
name 2	standard pressure part	标准受压件
name 2	stay and staybolt	支撑件及拉撑螺栓
name 2	staying formed head	成型封头的支撑
name 2	stiffening ring	刚性环
name 2	stub end	(翻边）管接头
name 2	stud bolt	双头螺栓
name 2	support	支座，支承
name 2	support of large vessel	大容器支座
name 2	support of vessel	容器支撑
name 2	surfaces exposed and component part	暴露的表面和部件部分
name 2	tie rod	拉杆
name 2	tongue and groove facing flange	榫槽面法兰
name 2	transition	过渡段
name 2	tray	塔盘
name 2	tube and pipe	管子
name 2	tubing	管子件
name 2	u expansion joint	U型膨胀节
name 2	vortex breaker	防涡流挡板
name 2	washer	垫圈
name 3	access opening	通道孔
name 3	adjacent to edges of staybolted surface	邻近于螺栓拉撑的表面周边处
name 3	area supported	支撑面
name 3	around opening for welded attachment	环绕焊接附件孔口
name 3	braced and stayed surface	支持和支撑面
name 3	corner and fillet	圆角和倒角
name 3	flange connection	法兰连接
name 3	flange contact facing	法兰接触面
name 3	flued opening in	翻边开孔
name 3	graphite	石墨
name 3	hole	小孔
name 3	hole for screw	螺孔
name 3	hole in joint	接头处的孔
name 3	hub	高颈
name 3	knuckle	过渡圆角
name 3	knuckle radiu	转角半径
name 3	large opening	大开孔
name 3	ligament	孔桥，孔排
name 3	long radius	大弯曲半径
name 3	minimum number of pipe threads for connection	管螺纹连接的最少螺纹牙数
name 3	multiple opening	多个开孔
name 3	opening adjacent to weld	邻近焊缝的开孔
name 3	opening exceeding size limit of standard	大开孔
name 3	opening in shell	壳体上开孔
name 3	opening subject to rapid pressure fluctuation	经受压力突然波动的开孔
name 3	opening through or near welded joint	通过或靠近焊缝处的开孔
name 3	outlet	排放口
name 3	pitch	节距
name 3	pressure boundary	承压边缘
name 3	protective device	防护装置
name 3	reaming hole for screw stay	为固定螺钉用的铰孔
name 3	ring-joint gasket and groove	环形垫片的垫片槽
name 3	sharp angle	尖角
name 3	short radius	小弯曲半径
name 3	single-wall	单层
name 3	special construction	特殊结构
name 3	special sharp	特殊形状
name 3	spherical sections of vessel	容器的球形部分
name 3	stayed surface	支撑表面
name 3	structural	结构
name 3	stud bolt thread	双头螺栓螺纹
name 3	studded connection	双头螺纹连接
name 3	taper	锥度
name 3	telltale hole	指示孔
name 3	thick shell	厚壳体
name 3	thickness	厚度
name 3	thickness of shell	壳体厚度
name 3	threaded	螺纹
name 3	threaded connection	螺纹连接
name 3	threaded inspection openings	螺纹检查孔
name 3	thread	螺纹
name 3	transition in cylindrical shell	柱状壳体的过渡
name 3	upset for threading	为车制螺纹的镦粗
name 3	zones of different	不同区域
name 4	abrasion	磨损
name 4	adjustment	调节
name 4	area	区域
name 4	external surface	外表面
name 4	internal surface	内表面
NDE	certification of nondestructive personnel	无损检验人员证明书
NDE	destructive	破坏性
NDE	flaw	瑕疵
NDE	gamma ray	γ射线
NDE	indication	指示
NDE	liquid penetrant examination	液体渗透检验
NDE	magnetic particle	磁粉
NDE	magnetic particle examination	磁粉检测
NDE	penetrant examination	渗透检验
NDE	radiograph	射线照相
NDE	radiograph factor	射线照相系数
NDE	radiographic examination	射线超声检验
NDE	radiographing	射线照相
NDE	radium capsule	装镭的盒子
NDE	round indication	圆形显示
NDE	spot examination of welded joint	焊接接头的抽样检查
NDE	ultrasonic examination	超声检验
NDE	ultrasonic examination of weld	焊缝的超声检验
paint	blast	喷砂
paint	coat thickness	涂层厚度
paint	colour	颜色
paint	finish coat/ top coat	面漆
paint	intermediate coat/ middle coat	中间漆
paint	painting system	油漆系统
paint	primer coat/ under coat	底漆
paint	sagging	流挂
paint	scale off	剥落
paint	stain	锈蚀
quality	abrupt ridge-or-valley	棱角度
quality	acceptance by inspector	由检查员认为合格
quality	access to plant	在厂内应有的便利
quality	accessibility	可达性
quality	acid pickling	酸洗
quality	additional requirement	附加要求
quality	alignment	找准
quality	alignment tolerance	对准公差
quality	ammonia leak test	氨渗漏试验
quality	approval of repair	修补的批准
quality	ball passing test	通球试验
quality	basic requirement	基本要求
quality	certificate of authorization	授权
quality	certificate of authorization for code symbol stamp	规范符号标志的认可证书
quality	certification	证明
quality	chloride	氯化物
quality	code of organization	组织机构代码
quality	code symbol stamp	规范标志钢印
quality	combination test	组合试验
quality	combined with pneumatic	与气压试验混合的
quality	completed vessel	完工容器
quality	control	控制
quality	control of stamping	打（钢）印控制
quality	data report	数据报告
quality	declaration of conformity	符合性声明
quality	defined limit	规定的范围
quality	diameter	直径
quality	dimension	尺寸
quality	dimensional check	尺寸校核
quality	duty	职责
quality	eccentricity of shell	壳体的偏心度
quality	electro-polishing	电解抛光
quality	examination	检查
quality	examination of sectioned speciment	剖面试样的检验
quality	exempted from inspection	免检
quality	exemption	豁免
quality	expanding ratio	胀管率
quality	final inspection	最终终检（终检）
quality	girth	周长
quality	helium leak test	氦泄漏试验
quality	hydrostatic proof test	水压验证试验
quality	hydrostatic test/hydraulic test/hydrotest	水压试验
quality	inside diameter	内径
quality	inspection	检验
quality	inspection opening	检查孔
quality	inspector	检查师
quality	intermediate inspection	中间检查(中检）
quality	jurisdictional review	权限审查
quality	lack of soundness	致密性缺乏
quality	law covering pressure vessel	涉及压力容器的法规
quality	leakage test	泄漏试验
quality	length of skirt	直边长度
quality	levelness	水平度
quality	limit of out-of-roundness of shell	壳体不圆度的限制
quality	limitation	限制
quality	linearity	直线性
quality	mandatory	强制的
quality	mandatory minimum thickness	规定最小厚度
quality	manufacture license	制造许可
quality	manufacturer’s data report	制造厂数据报告格式
quality	manufacturer’s stamp	制造厂的印记
quality	marking	标志
quality	master stamping	主钢印
quality	measurement	测量
quality	mill under tolerance	钢厂负公差
quality	misalignment	错边量
quality	mock-up test	模拟试验
quality	nozzle orientation	管口方位
quality	offset of edges of plates at joint	在接头处板边的偏差
quality	orientation	方位
quality	out-of-roundness	不圆度
quality	outside	外径
quality	partial data report	零部件数据报告
quality	passivation	钝化
quality	perpendicular	垂线；垂直的位置
quality	pneumatic	气压
quality	pneumatic test	气压试验
quality	prior pressure application	在升压之前
quality	proof test	验证性试验
quality	quality control	质量管理
quality	quality control system	质量保证体系
quality	quality factor	质量系数
quality	radiu	半径
quality	record by manufacturer	由制造厂所作的记录
quality	report	报告
quality	requirement	要求
quality	responsibility	职责
quality	responsibility of manufacturer	制造者的职责
quality	retention of records	记录的保存
quality	retest	复试，复验
quality	roughness	粗糙度
quality	roundness	圆度
quality	roundness tolerance	不圆度公差
quality	sectioning of welded joint	焊接接头的剖面检验
quality	service restriction	使用限制
quality	shape deviation	形状偏差
quality	size	尺寸
quality	special equipment	特种设备
quality	specification	标准
quality	spot examination	抽样检查
quality	stamp	钢印，打钢印
quality	stamp location	打印位置
quality	stamping	标记
quality	standard	标准
quality	static head	静(压力)水头 ,静压头
quality	straightness	直线度
quality	supervision and inspection certificate	监督检验证书
quality	surface roughness	表面粗糙度
quality	test	试验
quality	test gage requirement	试验仪表要求
quality	test requirement	试验要求
quality	tests, hydrostatic proof	试验，水压验证
quality	thickness examination	厚度检查
quality	thickness gage	厚度量规
quality	tightness	紧密性
quality	tightness test	气密性试验
quality	time-based inspection	基于时间的检验
quality	tolerance	容差，允差
quality	tolerance grade not noted	未注尺寸公差
quality	tolerance	公差
quality	transfering marking	标志的移植
quality	use as is	回用
quality	vacuum test	真空试验
quality	verification test	验证试验
quality	vessels exempted from	免检容器
quality	vessels subjected to external pressure	承受外压的容器
quality	water quality	水质
quality	with code symbol	带有规范符号
safety	bursting disk	爆破压力
safety	drainage, discharge from safety and relief valves	由安全阀、泄压阀排放和泄放
safety	explosive	爆炸的
safety	rupture disk	爆破片
safety	adjacent to safety and relief valve	邻近于安全和泄压阀
safety	adjustable blow down	可调节的泄放
safety	discharge	泄放，排放
safety	discharge of safety valve	安全阀泄放
safety	emergency shutoff device	紧急切断装置
safety	from vessels to safety valve	由容器至安全阀
safety	juice level gauge	液位计
safety	multiple safety valve	多个安全阀
safety	pressure gauge	压力表
safety	relieving capacity of safety valve	安全阀排量
safety	rupture disk device	爆破片装置
safety	safety and relief valve	安全和泄压装置
safety	safety devices/accessories	安全附件
safety	safety relief and pressures relief valve	安全泄放和泄压阀
safety	safety valve	安全阀
safety	setting safety valve	整定安全阀
safety	springs for safety valve	安全阀的弹簧
safety	stop valve	截止阀
safety	stop valves adjacent to	邻近的截止阀
safety	thermometric indicator	测温仪表
safety	valve	阀门
safety	pressure-relieving devices	泄压装置
safety	relief device	泄放装置
safety	relief valve	泄压阀
safety	safety	安全性
weld	actual thickness	实际厚度
weld	amount of overlap	搭接量
weld	arc and gas welded joint	电弧焊和气焊接头
weld	arc seam weld	电弧缝焊缝
weld	arc spot weld	电弧焊点
weld	arc strike	碰弧
weld	arc welding	弧焊
weld	arc welding electrode	弧焊电极
weld	as brazed	钎焊态
weld	attachment around opening	开孔周围的连接
weld	autogenous weld	自熔合焊缝
weld	automatic brazing	自动钎焊
weld	avoid at weld edge	避免在焊缝边上
weld	back gouging	背面清根
weld	backhand welding	右焊法
weld	backing	衬垫
weld	backing gas	背面保护气
weld	bare electrode	裸电极
weld	base metal	母材
weld	bond line	熔合线
weld	braze	钎焊
weld	brazed connection for nozzle	接管的钎焊连接
weld	brazed joint	钎焊接头
weld	brazed vessel	钎焊容器
weld	brazer	钎焊工
weld	brazing	钎焊
weld	built-up of base metal	母材补焊
weld	butt weld	对接焊缝
weld	buttering	堆焊隔离层
weld	carbon electrode	碳电极
weld	cleaning of brazed surface	钎焊表面清理
weld	cleaning of welded surface	焊件表面清理
weld	clearance between surfaces to be brazed	钎焊表面间的间隙
weld	complete fusion	完全熔合
weld	composite	复合材料
weld	composite electrode	复合焊丝
weld	consumable insert	可熔化嵌条
weld	contact tube	导电嘴
weld	continous weld	连续焊
weld	corner joint	角接头(互成直角）
weld	corner weld	角接焊缝
weld	corrosion resistant weld metal	耐蚀层
weld	cover pass	盖面焊道
weld	covered electrode	涂药焊条
weld	defect	缺陷
weld	dewell	驻留
weld	dip brazing	浸沾钎焊
weld	direct current	直流电
weld	discontinuity	不连续处
weld	dissimilar weld metal	不同金属的焊接
weld	double-bevel groove weld	K型坡口
weld	double-vee groove weld	X型坡口
weld	double-welded joint	双面焊对接接头
weld	double-welded lap joint	双面焊搭接接头
weld	effective thickness	有效厚度
weld	electric resistance	电阻
weld	electric resistance welding	电阻焊
weld	electroslag welding electrode	电渣焊电极
weld	equal leg fillet weld size	等焊脚焊缝尺寸
weld	ferrite number	铁素体数
weld	filler metal	填充金属
weld	filler metal	填充金属（焊丝）
weld	filler plugs for trepanned hole	锥孔的管塞
weld	fillet	填角
weld	fillet weld	角焊缝
weld	flux	焊剂
weld	flux	焊剂
weld	flux	钎焊剂
weld	flux-cored electrode	药芯焊丝
weld	for connection to brazed vessel	用于对钎焊容器的连接
weld	formed head for welding	用于焊接成型封头
weld	frequency	频率
weld	fuel gas	燃料气体
weld	full fillet weld	满角焊缝
weld	fusion face	熔合面
weld	fusion line	熔合线
weld	girth joint	环缝接头
weld	groove weld	坡口焊缝
weld	hard-facing weld metal	表面加硬层
weld	heat affected zone	热影响区
weld	in welded joint	在焊缝上
weld	inserted strip	嵌条
weld	insertion of welded vessel	插入焊接容器
weld	interpass temperature	层间温度
weld	joint	接头
weld	joint in shell	壳体上的接头
weld	joint penetration	接头熔深
weld	keyhole welding	小孔焊
weld	lap	搭接
weld	lap joint	搭接接头
weld	lap or overlap	搭接长度
weld	lightly-coated electrode	薄药皮焊条
weld	limitation on welded vessel	焊接容器的限制
weld	longitudinal	纵向的
weld	longitudinal joint	纵向接头
weld	longitudinal under external pressure	在外压作用下纵向的
weld	lower transformation temperature	下转变温度
weld	manual welding	手工焊
weld	melt-in	填丝焊
weld	metal electrode	金属极
weld	on welded vessel	在焊接容器上
weld	oscillation	摆动
weld	overlay	堆焊
weld	pass	焊道
weld	peel test	剥离试验
weld	peening	锤击
weld	perfomance qualification	技能评定
weld	plug	塞焊
weld	plug weld	塞焊
weld	post heating	后热
weld	preheat maintenance	预热保温
weld	preheat temperature	预热温度
weld	preheating	预热
weld	preparation of plates for welding	焊接板材的准备
weld	procedure qualification	工艺评定
weld	qualification	评定
weld	rabbet joint	嵌接接头
weld	resistance brazing	电阻钎焊
weld	resistance welding electrode	电阴焊电极
weld	restoration of base metal thickness	母材厚度的修复
weld	retainer	成型块
weld	root gap	根部间隙
weld	seal weld	密封焊缝
weld	semiautomatic brazing	半自动钎焊
weld	single-bevel groove weld	单面V型坡口
weld	single-welded joint	单面焊接接头
weld	single-welded lap joint	单面搭接接头
weld	smooth transition	圆滑过渡
weld	specimen /test specimen	试样
weld	spot weld	焊点
weld	strength of brazed joint	钎焊接头的强度
weld	supplemental filler metal	附加填充金属
weld	surface weld metal buildup	金属堆焊表面
weld	tack	定位
weld	tack weld	定位焊
weld	tee-joint	丁字接头
weld	thermal cutting	热切割
weld	thermal spraying	热喷涂
weld	through welded joint	通过焊接接头
weld	tungsten electrode	钨极
weld	upper transformation temperature	上转变温度
weld	usability	工艺性
weld	weave bead	横摆焊道
weld	weld	焊接
weld	weld bead	焊道
weld	weld deposit	焊接熔敷金属
weld	weld face	焊接面
weld	weld interface	焊接界面
weld	weld metal	焊缝金属
weld	weld reinforcement	焊缝余高
weld	welded	焊接的
weld	welded carbon low-alloy pipe and tube	焊接低合金碳钢管
weld	welded joint	焊接接头
weld	welded joint category	焊接接头分类
weld	welded joint efficiency factor	焊接接头系数
weld	welded reinforcement of nozzle opening	接管开孔的焊缝补强
weld	welded surface	焊接表面
weld	welded vessel	焊接容器
weld	welded joint	焊接接头
weld	welder	焊工
weld	welding	焊接
weld	welding coefficient	焊接系数
weld	welding end of	焊接端
weld	welding joints	焊接接头
weld	welding neck flange	带颈对焊法兰
weld	welding operator	焊机操作工
weld	welding operator	自动焊工
weld	welding procedure	焊接工艺
weld	welding procedure specification	焊接工艺说明书
weld	weldment	焊件
weld	welds acceptability	焊缝合格
weld	test of qualification	评定试验
	assemble	装配
	attachment to shell	和壳体的装配
	before assembling	组装之前
	capacity certification	排放量证明
	complete	整个的
	connection for nozzle and attachment	用于接管和附件的连接
	connection to vessel	连接至容器
	covered	覆盖
	cylindrical	圆柱形
	definition	定义
	description	描述
	description of type	类型的描述
	detail	细节
	determination	确定
	during fabrication	制造期间
	entirely in spherical portion	全部在球体部分
	example	实例
	fabrication	制造
	fabrication technology	制造工艺
	fabricator	制造厂
	facility	装备
	field assembly	现场安装
	field assembly of vessel	容器的现场安装
	fire protection	防火
	fitting attachment	附件装配
	fitting up	组对
	fitting up joint	连接处的装配
	flat	平的
	free movement of vessel on support	支座上的容器活动不受约束
	indirect operation	间接操作
	installation	安装
	installation and operation	安装和运转
	installation on vessels in service	容器在役时的安装
	installation type	安装型式
	insulation	保温
	interpretation by standard procedure	由标准程序的说明
	laying out	划线
	location	位置
	made from pipe	由管子制造的
	manufacture	制造者
	match	匹配
	method of fabrication	制造方法
	miscellaneous	各种各样的，其它的
	multi-layered	多层
	nomenclature	术语
	omission	省略
	operating instruction manual	操作说明书
	pipe connection	管子的连接
	processe process	工艺
	production	生产
	progressive plastic deformation	过度塑性变形
	refilling	再填充
	sealless	无缝的
	sliding	滑动的
	stagger	错开
	supports to prevent	用支撑防止
	tapered	锥形的
	type	类型
	type of attachment	附件的类型
	unfired	非直接火
	unstayed	无支撑
	use of over thickness listed in section Ⅱ	采用超过列于第Ⅱ卷表中的厚度
	when not required	当不要求时
	when sectioned	解剖时

标签：专业英语,weld,name,压力容器,material,heat,design,储气罐,quality
From： https://www.cnblogs.com/cuishengli/p/18048449

压力容器、储气罐、压力容器焊接专业英语

相关文章

赞助商

阅读排行