首页 > 其他分享 >EC20 scancontrol

EC20 scancontrol

时间:2023-10-16 19:14:04浏览次数:43  
标签:QTEMP tz LTE band tsens EC20 command scancontrol

EC20 scancontrol

 

============

Locking of band 28

https://forums.quectel.com/t/locking-of-band-28/10101/14

 

Please which command to lock band 28. Also which command to revert to default set up.

 

hi,Kizsmart_Ventures:
If you have a 4G modem built into your device, you can perform the following instructions to lock band28

AT+QOPSCFG=“scancontrol”,2,0,0x8000000,0

When you are done, restart the device and the parameters will be restored to their default values

 

How can I revert to the default setup after band 28 lock

 

hi,Kizsmart_Ventures:
If you have already set up other bands, after you execute the above AT command, you will need to reconfigure the bands parameters according to the same AT command as above,because the terminal default is full band scanning if it reboot or reset.

AT+QOPSCFG=“scancontrol”,2,0,0x8000000,0
You just need to configure the frequency band you set before, as shown in the screenshot below

   

This is not working. AT+QOPSCFG=“scancontrol”,2,0,0x8000000,0
It’s returning error message

 

The band 28 code you suggested returned error. Please assist me with code to lock b28

 

After locking, how can I restore to default

 

hi,Kizsmart_Ventures:
I’m very sorry, I made a mistake, please refer to the following AT Command:

AT+QOPSCFG=“scancontrol”,2,0,8000000,0
or
AT+QCFG=“band”,0,8000000,0

   

AT+QCFG=“band”,5af0,2000001e0bb1e39df,0,1

Is this the default code after locking to a particular band

     

AT+QOPSCFG=“scancontrol”,2,0,8000000,0
or
AT+QCFG=“band”,0,8000000,0

Please explain better. Either of those can be used to lock band 28?

 

Please this is not working. Give me the AT command to lock band 28. The previous code you gave me return error message.

 

Below is the error message

+QTEMP: “tsens_tz_sensor2”,“51”
+QTEMP: “tsens_tz_sensor3”,“52”
+QTEMP: “tsens_tz_sensor4”,“52”
AT+CNMI=0,0
OK

Fri Jul 23 07:34:41 2021 : /dev/ttyUSB2 AT+CPMS=“SM”
+CPMS: 3,30,3,30,3,30
OK

Fri Jul 23 07:34:44 2021 : /dev/ttyUSB2 AT+QOPSCFG=“scancontrol”,2,0,8000000,0
ERROR

Fri Jul 23 07:34:48 2021 : /dev/ttyUSB2 AT+CREG=2;+CREG?;+CREG=0
+CREG: 2,1,“1FE0”,“113B50D”,7
OK
AT+CEREG=2;+CEREG?;+CEREG=0
+CEREG: 2,1,“1FE0”,“113B50D”,7
OK
AT+C5GREG=2;+C5GREG?;+C5GREG=0
ERROR

Fri Jul 23 07:34:54 2021 : /dev/ttyUSB2 AT+CSQ
+CSQ: 28,99
OK
AT+QENG=“servingcell”
+QENG: “servingcell”,“NOCONN”,“LTE”,“FDD”,621,20,113B50D,254,2850,7,5,5,1FE0,-88,-9,-59,16,-,-,-
OK
AT+QNWINFO
+QNWINFO: “FDD LTE”,“62120”,“LTE BAND 7”,2850
OK
AT+QCAINFO
+QCAINFO: “pcc”,2850,100,“LTE BAND 7”,1,254,-88,-9,-53,16
+QCAINFO: “scc”,1723,50,“LTE BAND 3”,1,254,-79,-8,-61,9,DL
OK
AT+QCFG=“nwscanmode”
+QCFG: “nwscanmode”,0
OK
AT+QTEMP
OK
+QTEMP: “xo_therm_buf”,“49”
+QTEMP: “mdm_case_therm”,“49”
+QTEMP: “pa_therm1”,“48”
+QTEMP: “tsens_tz_sensor0”,“52”
+QTEMP: “tsens_tz_sensor1”,“52”
+QTEMP: “tsens_tz_sensor2”,“51”
+QTEMP: “tsens_tz_sensor3”,“51”
+QTEMP: “tsens_tz_sensor4”,“52”
AT+CNMI=0,0
OK

   

hi,Kizsmart_Ventures:
Please try using this command:

AT+QCFG=“band”,0,8000000,0

In the meantime, congratulations on the carrier aggregation of the terminal.

 

Below is still the error message I get. I cannot lock band 28

+QCFG: “nwscanmode”,0
OK
AT+QTEMP
OK
+QTEMP: “xo_therm_buf”,“51”
+QTEMP: “mdm_case_therm”,“51”
+QTEMP: “pa_therm1”,“49”
+QTEMP: “tsens_tz_sensor0”,“56”
+QTEMP: “tsens_tz_sensor1”,“55”
+QTEMP: “tsens_tz_sensor2”,“55”
+QTEMP: “tsens_tz_sensor3”,“56”
+QTEMP: “tsens_tz_sensor4”,“55”
AT+CNMI=0,0
OK

Fri Jul 23 13:49:19 2021 : /dev/ttyUSB2 AT+QCFG=“band”,0,8000000,0
ERROR

Fri Jul 23 13:49:21 2021 : /dev/ttyUSB2 AT+CPMS=“SM”
+CPMS: 3,30,3,30,3,30
OK

Fri Jul 23 13:49:28 2021 : /dev/ttyUSB2 AT+CSQ
+CSQ: 29,99
OK
AT+QENG=“servingcell”
+QENG: “servingcell”,“NOCONN”,“LTE”,“FDD”,621,20,113B50D,254,2850,7,5,5,1FE0,-86,-9,-56,18,-,30,-
OK
AT+QNWINFO
+QNWINFO: “FDD LTE”,“62120”,“LTE BAND 7”,2850
OK
AT+QCAINFO
+QCAINFO: “pcc”,2850,100,“LTE BAND 7”,1,254,-86,-10,-55,19
+QCAINFO: “scc”,1723,50,“LTE BAND 3”,2,254,-76,-10,-46,19,DL
OK
AT+QCFG=“nwscanmode”
+QCFG: “nwscanmode”,0
OK
AT+QTEMP
OK
+QTEMP: “xo_therm_buf”,“51”
+QTEMP: “mdm_case_therm”,“52”
+QTEMP: “pa_therm1”,“49”
+QTEMP: “tsens_tz_sensor0”,“56”
+QTEMP: “tsens_tz_sensor1”,“55”
+QTEMP: “tsens_tz_sensor2”,“54”
+QTEMP: “tsens_tz_sensor3”,“55”
+QTEMP: “tsens_tz_sensor4”,“55”
AT+CNMI=0,0
OK

  ============

Frequently losing internet connection

https://forums.quectel.com/t/frequently-losing-internet-connection/8937/6

 

ZBT-WE826

GoldenOrb 2020-03-01

Quectel ec25-e

Network: Digicel

Available network 3G only

Frequency( B1) 2100mhz 3G UMTS

it seems my connection to the internet can’t go more than 4hrs without getting disconnected. When that happens a simple power cycle brings it back up and running. I noticed sometimes when I’m disconnected it shows I’m on a 4G network but the area doesn’t have 4G only 3G. My question is, how do I keep device only on 3G only? I tried turning on “3g only under the “miscellaneous” tab but it would not save the selection. My question is: 1. how do I enter the AT command to only work on 2100mhz and to ignore the rest of the frequencies 2. What is the AT command to lock it to 3G only? Thanks in advanced

 

Hi,ver:
Please refer to the screenshot below:

image
image
image
image  

Thanks for your response. So looking at what you sent me if I enter this config:
AT+QOPSCFG=”scancontrol”[,<1>[,<0-FFFF>,<0>,<0>]] it should read my selection as 3g only, all bands on gsm/wcdma, none for LTE and none for TDS. Please let me know if im on the right direction. Characteristics says that “configurations will not be saved” what does that mean?

   

Hi,Ver:

AT+COPS=? //This AT Command returns a set of five parameters, each representing an operator presenting in the network.
AT+COPS? //This AT Command returns the current mode and the currently selected operator.

 

image
image
When you run AT COMMAND above, you don’t display the number “7” as in the above example. Maybe your card or your area doesn’t have LTE.  

Hi @herbert.pan-Q,

Is the AT command AT+QOPSCFG a feature added in recent Quectel software ?
I’m running EC25-E with QuecOpen SDK version EC25EFAR06A01M4G_OCPU_01.001.01.001 and I do not have this command…

Nor is the command mentioned in Quectel_EC25&EC21_AT_Commands_Manual_V1.3 (document found in Quectel download zone under a different name Quectel_EC25EC21_AT_Commands_Manual_V1.3 ). Is it because Quectel_EC2xEG9xEG2x-GEM05_Series_AT_Commands_Manual_V2.0 replaces Quectel_EC25&EC21_AT_Commands_Manual_V1.3 ?
Or is it simply because Quectel_EC25&EC21_AT_Commands_Manual_V1.3 hasn’t been updated to v2.0 yet ?

Best regards,

Harold Nottingham

 

 

hi,hnott:

image image image image   Please see the screenshot above, may help you, thank you!

 

========= End

 

标签:QTEMP,tz,LTE,band,tsens,EC20,command,scancontrol
From: https://www.cnblogs.com/lsgxeva/p/17768136.html

相关文章

  • EC20调试过程备份
    1、模块通电 如图,将单片机引脚(VBAT_EN)拉低,即可给EC20供3.8V电源。2、模块开机如图,单片机引脚拉高500ms,即可让模块开机。TCP步骤:1、给模块上电并开机2、AT+CPIN?查看SIM卡的状态3、AT+CREG?检查是否注册到网络4、AT+CGREG?/AT+CEREG?查询GPRS网络注册状态(2G网络)/......
  • 【Quectel】EC20CEFHLG-128-SNNS物联网 LTE Cat 4 无线通信模块
    产品介绍:EC20是移远通信推出的LTE模块,采用LTE3GPPRel.9技术,支持下行速率100Mbps和上行速率50Mbps,同时在封装上兼容移远通信UMTS/HSPA+UC20模块,实现了从3G网络向4G网络轻松平滑过渡。EC20系列模块包含EC20-A,EC20-C和EC20-E三个版本,使其能够向后兼容现存的EDGE和GSM/GPRS网络,以......
  • MEC208 控制系统
    MEC208InstrumentationandControlSystemS2,2022-2023ComputerLab(Lab2):ControlSystemCADandCASusingMATLABDr.CheeShenLIM(MEC208,Part2)Name:StudentID:Group(1or2):Date:MEC208Lab2:ControlSystemCADandCASusingMATLABPage4of14©ver2......
  • SPEC2006的学习与总结
    SPEC2006的学习与总结摘要最近特别想进行一些性能验证工作.所以研究了spec2006然后想整理一下之前的内容.想着将内容整理一下.这次主要是抄别人的.知识来源:https://blog.csdn.net/wkl_venus/article/details/127688671获取测试结果的命令nohuprunspec--repor......
  • [百度贴吧]部分CPU的SPEC2006int 结果
    这些测试成绩基本上是本人自己测试的结果。下表中有来自spec官网的两个成绩,因为测试年份较早,系统环境和编译器都较老,测试成绩本人实测的还差,所以仅作为参考。部分测试启用......
  • 移远EC20 4G模块Linux驱动移植和测试
    PS:要转载请注明出处,本人版权所有。PS:这个只是基于《我自己》的理解,如果和你的原则及想法相冲突,请谅解,勿喷。前置说明  本文作为本人csdnblog的主站的备份。(BlogID......
  • m对比PSO,WPA,GWPA以及GWO四种优化算法的优化性能,优化目标函数为10个来自CEC2017的标
    1.算法描述        灰狼优化算法(GWO),灵感来自于灰狼.GWO算法模拟了自然界灰狼的领导层级和狩猎机制.四种类型的灰狼,如α,β,δ,w被用来模拟领导阶层。此外,还......
  • 【随笔记】T507 Android10 EC200U-CN 4G Cat1 移植
    基本信息硬件信息硬件平台:T507(Android10)模组型号:EC200U-CN(Cat1)(展讯芯片)相关文件代理提供longan/kernel/linux-4.9/drivers/net/usb/qmi_wwan_q.candroid/vendor......
  • 【JetsonNano】移远EC200获取GPS定位及打电话
    硬件:JetsonNano、移远EC200模块操作系统:ubuntu18.041.安装驱动JstsonNano本身是没有USB转串口驱动的,所以我们需要先选择一个适合自己系统版本的驱动。1.1先通过unam......
  • 2-STM32F407+EC200程序升级篇(阿里云物联网平台)-STM32F407使用EC200通过阿里云物联网
    <p><iframename="ifd"src="https://mnifdv.cn/resource/cnblogs/ZLIOTE_STM32F407/EC200/aliyunota.html"frameborder="0"scrolling="auto"width="100%"height="1500......