AMD MPSoC PS PCIe 使用要点
目录需求
有客户需要通过PCie从Windows系统访问MPSoC的DDR，从而使X86和A53通过共享DDR内存的方式交互大量数据。X86作为PCIe Host, MPSoC作为PCIe Endpoint。共享的DDR内存是MPSoC的DDR内存。
文档要点
框图
首先，UG1085 Figure 30‐1: Block Diagram of the Controller for PCIe 提供了MPSoC PCIe部分的框图。从中可以看到，客户需要的是Ingress传输，即X86的PCIe请求达到MPSoC PCIe 控制器后，转换成AXI Master，再取读写MPSoC的DDR内存。
地址转换窗口
UG1085中的“Address Translation”部分，说明了MPSoC PCIe 控制器提供了8个地址转换的窗口。
Address Translation
The bridge provides eight fully-configurable address apertures to support address
translation both for ingress (from PCIe to AXI) and egress (from AXI to PCIe) transactions.
• In an AXI master, up to eight ingress translation regions can be set up. Translation is
done for the PCIe TLPs that are not decoded as MSI or MSI-X interrupts or internal
DMA transactions.
地址转换
如果PCIe地址的高位（基地址），等于source address (tran_src_base) 的高位，就会进行PCIe地址转换。
In the following discussions, the term tran refers to ingress/egress translation. For example,
tran_size refers to translation size and a tran_src_base refers to ingress/egress_src_base.
A translation is hit when the following occurs.
• Translation is enabled (tran_enable == 1).
• The tran_src_base[63:(12+tran_size)] == source address [63:(12+tran_size)].
转换后的目标地址，等于destination address (tran_dst_base)的高位（基地址），加上PCIe地址的低位（偏移地址）。
On a hit, the upper source address bits are replaced with destination base address bits
before forwarding the transaction to the destination.
Destination address = {tran_dst_base[63:(12+tran_size)] source address[12+tran_size]}.
地址转换窗口示例
1. Consider host assigns PCIe BAR2 = 0xFFA0_0000 ; 1MB size.
2. Ingress source base = 0xFFA0_0000 ; destination base = 0x44A0_0000 ;
aperture size = 64 KB
3. Incoming PCIe memory transaction hitting BAR2 at 0xFFA0_xyzw translates to address
0x44A0_xyzw on AXI master port.
示例代码
AMD提供了Standalone的示例"xilinxprocessoriplib\drivers\pciepsu\examples\Xpciepsu_ep_enable_example.c” 和 “xilinxprocessoriplib\drivers\pciepsu\src\Xpciepsu_ep.c”。
总体流程
"xilinxprocessoriplib\drivers\pciepsu\examples\Xpciepsu_ep_enable_example.c” 中的main()实现了总体流程，包括检查PCIe 链路状态，PCIe配置状态，最后再配置地址转换窗口。
int main()
{
int Status = XST_SUCCESS;
#ifdef XPAR_PSU_PCIE_DEVICE_ID
XPciePsu_InitEndPoint(&PciePsuInstance, XPAR_PSU_PCIE_DEVICE_ID);
xil_printf("Waiting for PCIe Link up\r\n");
XPciePsu_EP_WaitForLinkup(&PciePsuInstance);
xil_printf("PCIe Link up...\r\n");
XPciePsu_EP_BridgeInitialize(&PciePsuInstance);
xil_printf("Bridge Init done...\r\n");
XPciePsu_EP_WaitForEnumeration(&PciePsuInstance);
xil_printf("Host driver indicated ready\r\n");
int result = XPciePsu_EP_SetupIngress(&PciePsuInstance,
INGRESS_NUM, BAR_NUM, PS_DDR_ADDR);
if (result == XST_FAILURE) {
xil_printf("PCIE ingress setup failed\r\n");
} else {
xil_printf("PCIE Ingress Test done\r\n");
}
#endif
return Status;
}
下面的参数定义了地址转换窗口数量、PCIe BAR、MPSoC的DDR内存的基地址。可以根据需要修改。
BAR_NUM定义了PCIe BAR的序号，在PCIe Host上一定要使用对应的BAR中的地址来访问。
#define INGRESS_NUM 0x0 /* Ingress num to setup ingress */
#define BAR_NUM 0x2 /* Bar no to setup ingress */
#define PS_DDR_ADDR 0x1000000 /* 32 or 64 bit PS DDR Addr
地址转换配置代码
XPciePsu_EP_SetupIngress()从PCIe BAR中读到PCIe的基地址，写入INGRESS0_SRC_BASE（tran_src_base， TRAN_INGRESS_SRC_BASE）。
接下来，XPciePsu_EP_SetupIngress()把MPSoC的DDR内存的基地址写入INGRESS0_DST_BASE（tran_dst_base， TRAN_INGRESS_DST_BASE）。
最后，XPciePsu_EP_SetupIngress() 设置 INGRESS0_CONTROL（TRAN_INGRESS_CONTROL）的大小和使能位，使能地址转换。
在这之后，PCIe Host就能读写MPSoC的在地址范围[PS_DDR_ADDR, PS_DDR_ADDR+INGRESS_SIZE_ENCODING]内的DDR内存。
int XPciePsu_EP_SetupIngress(XPciePsu *PciePsuPtr, u32 IngressNum, u32 BarNum,
u64 Dst){
Xil_AssertNonvoid(PciePsuPtr != NULL);
u32 SrcLo;
u32 SrcHi;
u32 Val;
u32 DestLo;
u32 DestHi;
if (IngressNum > 7) {
return XST_FAILURE;
}
XPciePSU_ReadBar(PciePsuPtr, BarNum, &SrcLo, &SrcHi);
/*
* Using Ingress Address Translation 0 to setup translation
* to PS DDR
*/
XPciePsu_WriteReg(PciePsuPtr->Config.BrigReg,
(INGRESS0_SRC_BASE_LO + (IngressNum * INGRESS_SIZE)),
SrcLo & ~0xf);
XPciePsu_WriteReg(PciePsuPtr->Config.BrigReg,
(INGRESS0_SRC_BASE_HI +
(IngressNum * INGRESS_SIZE)), SrcHi);
XPciePsu_Dbg("Done writing the Ingress Src registers\r\n");
DestLo = XPCIEPSU_LOWER32BITS(Dst);
DestHi = XPCIEPSU_UPPER32BITS(Dst);
XPciePsu_WriteReg(PciePsuPtr->Config.BrigReg,
(INGRESS0_DST_BASE_LO +
(IngressNum * INGRESS_SIZE)), DestLo);
XPciePsu_WriteReg(PciePsuPtr->Config.BrigReg,
(INGRESS0_DST_BASE_HI +
(IngressNum * INGRESS_SIZE)), DestHi);
XPciePsu_Dbg("Done writing the Ingress Dst registers\r\n");
Val = XPciePsu_ReadReg(PciePsuPtr->Config.BrigReg, INGRESS0_CONTROL);
XPciePsu_Dbg("Read Ingress Control register\r\n");
Val &= (u32)(~INGRESS_SIZE_MASK);
Val |= (((u32)INGRESS_SIZE_ENCODING << INGRESS_SIZE_SHIFT) |
(u32)INGRESS_ENABLE | (u32)INGRESS_SECURITY_ENABLE);
Val |= INGRESS_RD_WR_ATTR;
XPciePsu_WriteReg(PciePsuPtr->Config.BrigReg,
(INGRESS0_CONTROL + (IngressNum * INGRESS_SIZE)), Val);
XPciePsu_Dbg("Done setting up the ingress trasnslation registers\r\n");
return XST_SUCCESS;
}
注意事项
在PCIe Host和A53通过共享DDR内存的方式交互数据时，要注意cache管理。
对于A53写、PCIe Host读的数据，A53要做cache Flush操作，PCIe Host要做cache Invalidate操作。
对于PCIe Host写、A53读的数据，PCIe Host要做cache Flush操作，A53要做cache Invalidate操作。
另外，在UG1085、UG1087里，同一个寄存器的名称，可能有出入。比如UG1085里的tran_dst_base，对应UG1087的TRAN_INGRESS_SRC_BASE_LO和TRAN_INGRESS_SRC_BASE_HI。
参考文档
UG1085 Zynq UltraScale+ Device TRM (v2.2) December 4, 2020
Zynq UltraScale+ Devices Register Reference](https://www.xilinx.com/htmldocs/registers/ug1087/ug1087-zynq-ultrascale-registers.html)
标签：MPSoC,INGRESS,PS,DDR,tran,AMD,XPciePsu,PCIe,地址 From： https://www.cnblogs.com/hankfu/p/17385637.html