首页 > 其他分享 >Fundamentals of Photonics

Fundamentals of Photonics

时间:2024-12-03 20:22:57浏览次数:9  
标签:fiber waveguides Fundamentals system Photonics each waveguide your

Fundamentals of Photonics Fall 2024 Project description

Due: December 04th 4pm

Design a fiber-waveguides-fiber transmission system based on Silicon (n=3.5) and SiO2 (n=1.5). with ultra large bandwidth , compact and  robust to +5nm variations with a total area of less than 1mm2. The system is composed of :

· fiber-waveguide coupler

· 1x2 splitters

· 1mm long waveguides

your goal is to ensure that A. the time delay for all channels is uniform. for all wavelength. This is determined by the dispersion of the 1mm waveguide. B. the transmission for all channels is uniform. and maximum. This is determined mainly by the splitting ratio and by the fiber-waveguide coupling, respectively.

Your input laser emits 10mW light from 1300nm to 1700nm. At the output of each channel there should be at least 1mW (due to the responsivity of the fiber coupled detectors). Assume that the output waveguides and the input laser is coupled to a fiber. with a mode profile that extends in one dimension (x) as where xo=5 microns . In other direction the mode extends infinitely (ie it is a slab-like waveguide). For all waveguides the bottom cladding is 3 micron thick.

Instructions:

· When using bends, the minimum bending radius is 5 microns for the maximum confined single mode waveguide  and 20 microns for a 10 times thinner waveguide. To find the radius for waveguides with in-between widths, linearly interpolate between these two extremes.

· Start by designing each of the components for 1500nm and then optimize them for wide bandwidth. Finally check (and optimize further if needed ) robustness to variations.

· When considering variations of +5nm, assume that All dimensions in all waveguides vary by 5nm.

· Use normalized parameters for all 代写Fundamentals of Photonics your calculations. For the fiber-waveguide coupler

· neglect reflections when calculating the transmission (ie include only overlap). Also assume that both waveguide and fiber are slab waveguide, ie infinite in one dimension.

· For the 1x2 splitter show (using plots) what is the most sensitive dimensions to variations and the just vary that dimensions. Calculate the change in amplitude at a given propagation length and then integrate the function numerically.

· For the 1mm waveguide with minimal dispersion, in order to find the optimal change of width as a function of propagation length:

o I. Choose a profile of the waveguide, discretize the waveguide along the propagation length every wavelength (this ensures that the discretization is fine enough while not requiring you to check the optimal discretization steps) and average the waveguide width over each discretized section.

o II. Calculate the amplitude in a higher order mode exiting the discretized section considering that the input into the section is a fundamental mode A. Note that when calculating the amplitude in a higher order consider that the propagation length of discretized section is much smaller than the coupling rate. therefore the amplitude in a higher order should be independent of the discretization.

o III. If B/A is higher than 1% , change the profile to decrease the probability and repeat the process from II.

· Decide what is the wavelength range that your laser will operate (within the larger range of 1300-1700nm). Then decide how many channels your system will have. Build an 1xn (n>2) splitter by cascading 1x2 splitters)

· State what is the total bandwidth supported by your system (in THz). Note 1nm bandwidth is equal to 133GHz bandwidth.

· Plot a schematic of whole system (include all relevant dimensions in the schematics) and estimate the total area of the system.

· Plot the transmission out of each channel as a function of wavelength for both optimized and non-optimized geometry

· Plot the time delay of each channel (assume that the delay is only induced by the 1mm long waveguide) as a function of wavelength for both optimized and non-optimized geometry. The time delay is given by:

 

The project should be done either individually or in teams(preferred) by groups of up to 3 members. Please have a section that explains clearly what was the role of each group member. The project should be done using your favorite code writing software (matlab, mathematica, etc)  for your calculations and plotting your data. All assumptions and choices you made (dimensions, number of waveguides, etc) should be discussed. Neglect reflections.

 

标签:fiber,waveguides,Fundamentals,system,Photonics,each,waveguide,your
From: https://www.cnblogs.com/BUS001/p/18584976

相关文章

  • COMP 218 Fundamentals of Object-Oriented Programming
    ©Maynotbecopiedorduplicatedwithoutthepermissionoftheowner.COMP218FundamentalsofObject-OrientedProgrammingAssignment1Pleasenote:youareNOTallowedtoposttheassignment/solutionanywhereontheInternet.IntellectualPropertyrightsa......
  • .Fundamentals.of.Software.Architecture.
    研究背景研究问题:本书旨在解决软件架构师在职业发展过程中面临的挑战,特别是如何从一个技术专家转变为一名能够领导团队并做出战略决策的架构师。研究难点:该问题的研究难点包括:软件架构的定义不明确,角色责任广泛且不断扩展,软件开发生态系统快速变化,以及许多过时的技术和解......
  • Fundamentals of Machine Learning for Predictive Data Analytics Algorithms, Worke
    主要内容:本书介绍了机器学习在预测数据分析中的基本原理、算法、实例和案例研究,涵盖了从数据到决策的整个过程。书中涉及机器学习项目生命周期的各个方面,包括数据准备、特征设计和模型部署。结构:本书分为五个部分,共计14章和若干附录:引言(IntroductiontoMachineLearn......
  • 《Fundamentals of Power Electronics》——理想变压器基本公式推导
    接下去推导理想变压器的基本公式。理想变压器满足以下三个条件:1、无铜损。假设原副边线圈均无纯电阻,则不会因在铜导线中产生焦耳热引起能量损耗,另外也不考虑回路中的分布电容。2、无铁损。忽略通过铁芯的磁通量变化引起的涡流损耗,忽略磁滞损耗,即铁芯由极端的软磁材料制成。3......
  • Fundamentals of Networks and Security – 4CM507
    FundamentalsofNetworksandSecurity–4CM507ContentsModuleLeaderKeydatesanddetailsDescriptionoftheassessmentAssessmentContentBackground:Casestudy-LocalAreaNetworkDesign:CompliancewithRequirementIntroductionGeneralrequi......
  • COSC2531 Programming Fundamentals
    Programming Fundamentals (COSC2531)FinalCodingChallengeAssessmentType Individual assessment (no group work).SubmitonlineviaCanvas/Assignments/FinalCodingChallenge.Marksareawardedperrubric(pleaseseetherubricon Canvas). Cla......
  • 《Fundamentals of Power Electronics》——保角映射
    ......
  • 【Docker系列】Section 1: Docker and Container Fundamentals①
    本篇是根据《KubernetesandDocker–AnEnterpriseGuide》整理出来的,原著作者:ScottSurovich|MarcBoorshtein,大家可以关注一下。Whothisbookisfor❓我们创建这本书是为了帮助DevOps人员团队扩展他们的技能,超越Kubernetes的基础知识。它是根据我们在多个企业环境......
  • 0x02 Linux Fundamentals Part 3
    Task1、引言这个房间将展示一些您可能日常的实用程序和应用程序,还将通过学习自动化、包管理和服务/应用程序日志记录来提高您的Linux-fu技能。Task2、部署Linux机器 Task3、终端文本编辑器①Nano用法:nanofilename 功能:搜索文本复制和粘贴跳转到行号找出您所在......
  • 0x01 Linux Fundamentals Part 2
    Task1、引言参数介绍复制文件和移动文件介绍文件和文件夹安全的访问机制以及如何识别当前用户对文件的访问权运行脚本和执行文件Task2、利用SSH接入远程主机什么是SSH及其工作原理?SSH只是一种加密形式的设备之间的协议。通过网络传输的数据都会被加密,形式如下图: st......