首页 > 其他分享 >NETDMIS5.0角度计算2023

NETDMIS5.0角度计算2023

时间：2023-04-03 12:03:04浏览次数：47  
标签：NETDMIS5.0 FALSE POINT 2023 CART 10.0000 FA 角度 1.00000000


按有效的元素组合形式计算两矢量元素（或其法线）之间的夹角。

路径：【 公差】 →【 角度】

NETDMIS5.0角度计算2023_算法


NETDMIS5.0角度计算2023_python_02


元素 1 与元素 2:选择两元素计算角度。 可用拖拽或鼠标中键添加元素。

投影面:选择计算角度是平面角度还是空间角度。 选择 SPACE， 角度计算与两元素先后顺序无关， 矢量角结果都是正的；

选择三个坐标平面， 先将元素矢量方向投影到对应坐标平面上再计算， 且计算与两元素先后顺序有关， 矢量角结果有正有负，

判断方法是大拇指垂直投影面，指向正轴（ XY 平面指向 Z+轴）， 按右手定则逆时针为正， 顺时针为负。

角度类型： 选择计算结果的角度类型。 矢量角计算的是两元素矢量方向间的角度， 矢量角结果从-180 度到+180 度。 选择余角后结果是 90-矢量角， 选择补角结果是 180/360-矢量角。选择锐角/钝角与元素的矢量和顺序无关， 结果都为正值。

有效元素组合形式如下：

1.直线（ 轴线） 与直线（ 轴线）

2.平面与平面

3.直线（ 轴线） 与平面

NETDMIS5.0角度计算2023_矩阵_03


NETDMIS5.0角度计算2023_DMIS_04

T(角度1)=TOL/ANGLB,90.0000,-0.5000,0.5000,XYPLAN
DMESW/COMAND,'OUTPUT/UNIT,ANGLE/ANGDEC,TYPE/0'
OUTPUT/FA(直线4),FA(直线5),TA(角度1)

NETDMIS5.0角度计算2023_NETDMIS_05


NETDMIS5.0角度计算2023_算法_06

$$ NET_DMIS_20160720
$$ MADE IN DE 2023-2-23 9:25:24
INCLUD/DMIS,'NET_DMIS_DEFINES.DMI'
INCLUD/DMIS,'VARDEFINE'
DMESW/COMAND,'PROBE_VAL/INIT'
UNITS/MM,ANGDEC
D(MACHINE)=DATSET/MCS
DMESW/COMAND,'COORDSYS/ALIGN'
WKPLAN/XYPLAN
PRCOMP/ON
PRCOMP/ON
FEDRAT/POSVEL,MMPS,300.0000
ACLRAT/POSACL,MMPSS,100.0000
FEDRAT/MESVEL,MMPS,20.0000
ACLRAT/MESACL,MMPSS,100.0000
SNSET/RETRCT,1.0000
SNSET/SEARCH,5.0000
SNSET/APPRCH,1.0000
DMESW/COMAND,'SNSET/MANRETRCT,1.0000'
DMESW/COMAND,'REPORT/CLEAR'
MODE/MAN
DID(D2L40)=DEVICE/STOR,'D2L40'
OPEN/DID(D2L40),SNS
S(A0B0)=SNSDEF/PROBE,INDEX,POL,0.0,0.0,0.0000,0.0000,1.0000,189.6500,2.0000
SNSLCT/SA(A0B0)
DMESW/COMAND,'SNSET/MANRETRCT,1.0000'
GEOALG/PLANE,LSTSQR
F(平面1)=FEAT/PLANE,CART,25.2397,24.4025,0,0,0,1.00000000
MEAS/PLANE,F(平面1),3
PTMEAS/CART,5.8670,61.1602,0,0,0,1.00000000
PTMEAS/CART,7.9742,5.9019,0,0,0,1.00000000
PTMEAS/CART,61.8779,6.1455,0,0,0,1.00000000
ENDMES
SNSET/DEPTH,0
DMESW/COMAND,'CONST/SET_PROJ_VEC,FA(平面1),1'
F(直线1)=FEAT/LINE,UNBND,CART,3.9902,0,-2.5682,0.99998216,0,0.00597311,0,-1.00000000,0
MEAS/LINE,F(直线1),2
PTMEAS/CART,3.9902,0,-2.3945,0,-1.00000000,0
PTMEAS/CART,62.1498,0,-2.3945,0,-1.00000000,0
ENDMES
F(点1)=FEAT/POINT,CART,0,3.8511,-2.1558,-1.00000000,0,0
MEAS/POINT,COMP,DME,F(点1),1
PTMEAS/CART,0,3.8511,-2.1558,-1.00000000,0,0
ENDMES
DATDEF/F(平面1),DAT(A_平面1)
D(坐标系1_S)=DATSET/DAT(A_平面1),ZDIR
D(坐标系1_R)=ROTATE/ZAXIS,FA(直线1),XDIR
D(坐标系1_T)=TRANS/ZORIG,FA(平面1)
D(坐标系1_T)=TRANS/YORIG,FA(直线1)
D(坐标系1_T)=TRANS/XORIG,FA(点1)
DMESW/COMAND,'COORDSYS/CAD=PART'
SAVE/DA(坐标系1)
MODE/AUTO,PROG,MAN
DMESW/COMAND,'SNSET/MANRETRCT,2.0000'
DMESW/COMAND,'CLEARP/ZDIR,10.0000,ZDIR,10.0000,ON'
F(平面2)=FEAT/PLANE,CART,31.9074,47.2202,0,0,0,1.00000000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_PLANEPOINTS_1006),AUTOFIGURE,F(平面2),PLANE,CART,LSTSQR,31.9074,47.2202,$
0,0,0,1.00000000,FALSE,FALSE,FALSE,10.0000,"CUR",TRUE,FALSE,POINTS,'12,3.1896,6.0668,0,0,0,1.00000000,$
3.8052,44.3397,0,0,0,1.00000000,2.8756,61.1914,0,0,0,1.00000000,20.2596,82.7555,0,0,0,1.00000000,34.2429,$
94.0982,0,0,0,1.00000000,58.7270,94.5314,0,0,0,1.00000000,60.6388,65.0396,0,0,0,1.00000000,57.5545,15.7291,$
0,0,0,1.00000000,59.8138,2.7359,0,0,0,1.00000000,19.3667,5.7715,0,0,0,1.00000000,21.3901,44.7369,0,0,$
0,1.00000000,41.0254,49.6460,0,0,0,1.00000000',TOUCH,0.3000,XYPLAN
F(直线2)=FEAT/LINE,BND,CART,3.0000,0,-2.0000,64.0000,0,-2.0000,0,-1.00000000,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_LINE_1007),AUTOFIGURE,F(直线2),LINE_BND,CART,3.0000,0,-2.0000,1.00000000,$
0,0,61.0000,FALSE,FALSE,FALSE,10.0000,"CUR",TRUE,FALSE,0,-1.00000000,0,4,0,0,0,TOUCH,0.3000,XYPLAN,0,$
0,LINE,"","","EXT1","EXT2","EXT3",ENDCAL
F(直线3)=FEAT/LINE,BND,CART,0,4.0000,-2.0000,0,60.0000,-2.0000,-1.00000000,0,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_LINE_1007),AUTOFIGURE,F(直线3),LINE_BND,CART,0,4.0000,-2.0000,0,1.00000000,$
0,56.0000,FALSE,FALSE,FALSE,10.0000,"CUR",TRUE,FALSE,-1.00000000,0,0,4,0,0,0,TOUCH,0.3000,XYPLAN,0,0,$
LINE,"","","EXT1","EXT2","EXT3",ENDCAL
F(点2)=FEAT/POINT,CART,0,0,-2.0000,0,0,-1.00000000
CONST/POINT,F(点2),INTOF,FA(直线2),FA(直线3)
DATDEF/F(平面2),DAT(A_平面2)
D(坐标系2_S)=DATSET/DAT(A_平面2),ZDIR
D(坐标系2_R)=ROTATE/ZAXIS,FA(直线2),XDIR
D(坐标系2_T)=TRANS/XORIG,FA(点2),YORIG,FA(点2)
D(坐标系2_T)=TRANS/ZORIG,FA(平面2)
SAVE/DA(坐标系2)
F(圆1)=FEAT/CIRCLE,INNER,CART,31.5000,31.5000,0,0,0,1.00000000,20.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆1),CIRCLE,INNER,CART,LSTSQR,31.5000,31.5000,$
0,0,0,1.00000000,20.0000,-1.00000000,0,0,5,-2.0000,0,0,0,0,360.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",'7,0,0,0,0,3.0000,0,10','0,1,0,$
5.0000',"EXT3",ENDCAL
F(圆2)=FEAT/CIRCLE,INNER,CART,31.5000,49.5000,0,0,0,1.00000000,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆2),CIRCLE,INNER,CART,LSTSQR,31.5000,49.5000,$
0,0,0,1.00000000,10.0000,-1.00000000,0,0,5,-2.0000,0,0,0,0,360.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",'7,0,0,0,0,3.0000,0,10','0,1,0,$
5.0000',"EXT3",ENDCAL
F(圆3)=FEAT/CIRCLE,INNER,CART,15.9115,40.5000,0,0,0,1.00000000,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆3),CIRCLE,INNER,CART,LSTSQR,15.9115,40.5000,$
0,0,0,1.00000000,10.0000,-1.00000000,0,0,5,-2.0000,0,0,0,0,360.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",'7,0,0,0,0,3.0000,0,10','0,1,0,$
5.0000',"EXT3",ENDCAL
F(圆4)=FEAT/CIRCLE,INNER,CART,15.9115,22.5000,0,0,0,1.00000000,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆4),CIRCLE,INNER,CART,LSTSQR,15.9115,22.5000,$
0,0,0,1.00000000,10.0000,-1.00000000,0,0,5,-2.0000,0,0,0,0,360.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",'7,0,0,0,0,3.0000,0,10','0,1,0,$
5.0000',"EXT3",ENDCAL
F(圆5)=FEAT/CIRCLE,INNER,CART,31.5000,13.5000,0,0,0,1.00000000,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆5),CIRCLE,INNER,CART,LSTSQR,31.5000,13.5000,$
0,0,0,1.00000000,10.0000,-1.00000000,0,0,5,-2.0000,0,0,0,0,360.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",'7,0,0,0,0,3.0000,0,10','0,1,0,$
5.0000',"EXT3",ENDCAL
F(圆6)=FEAT/CIRCLE,INNER,CART,47.0885,22.5000,0,0,0,1.00000000,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆6),CIRCLE,INNER,CART,LSTSQR,47.0885,22.5000,$
0,0,0,1.00000000,10.0000,-1.00000000,0,0,5,-2.0000,0,0,0,0,360.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",'7,0,0,0,0,3.0000,0,10','0,1,0,$
5.0000',"EXT3",ENDCAL
F(圆7)=FEAT/CIRCLE,INNER,CART,47.0885,40.5000,0,0,0,1.00000000,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆7),CIRCLE,INNER,CART,LSTSQR,47.0885,40.5000,$
0,0,0,1.00000000,10.0000,-1.00000000,0,0,5,-2.0000,0,0,0,0,360.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",'7,0,0,0,0,3.0000,0,10','0,1,0,$
5.0000',"EXT3",ENDCAL
F(点3)=FEAT/POINT,CART,41.5000,31.5000,-3.0000,-1.00000000,0,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_POINT_1007),AUTOFIGURE,F(点3),POINT,CART,DME,41.5000,31.5000,-3.0000,-1.00000000,$
0,0,0,0,0,FALSE,FALSE,FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"","EXT1","EXT2",$
"EXT3",ENDCAL
F(点4)=FEAT/POINT,CART,31.5000,41.5000,-3.0000,0,-1.00000000,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_POINT_1007),AUTOFIGURE,F(点4),POINT,CART,DME,31.5000,41.5000,-3.0000,0,$
-1.00000000,0,0,0,0,FALSE,FALSE,FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",$
"EXT1","EXT2","EXT3",ENDCAL
F(点5)=FEAT/POINT,CART,21.5000,31.5000,-3.0000,1.00000000,0,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_POINT_1007),AUTOFIGURE,F(点5),POINT,CART,DME,21.5000,31.5000,-3.0000,1.00000000,$
0,0,0,0,0,FALSE,FALSE,FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"","EXT1","EXT2",$
"EXT3",ENDCAL
F(点6)=FEAT/POINT,CART,31.5000,21.5000,-3.0000,0,1.00000000,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_POINT_1007),AUTOFIGURE,F(点6),POINT,CART,DME,31.5000,21.5000,-3.0000,0,$
1.00000000,0,0,0,0,FALSE,FALSE,FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",$
"EXT1","EXT2","EXT3",ENDCAL
GEOALG/CIRCLE,LSTSQR
DMESW/COMAND,'CONST/SET_PROJ_VEC,FA(XY),1'
F(圆8)=FEAT/CIRCLE,INNER,CART,31.5000,31.5000,-3.0000,0,0,1.00000000,20.0000
CONST/CIRCLE,F(圆8),BF,FA(点3),FA(点4),FA(点5),FA(点6)
DMESW/COMAND,'OUTPUT/NOM,FEAT/圆8,DIA/20.0000'
T(直径)=TOL/DIAM,0.0200,0.0000,MINMAX
DMESW/COMAND,'OUTPUT/UNIT,DIMENSION/MM'
DMESW/COMAND,'OUTPUT/UNIT,ANGLE/ANGDEC'
DMESW/COMAND,'OUTPUT/VECTOR,OFF'
OUTPUT/FA(圆8),TA(直径)
T(圆度1)=TOL/CIRLTY,0.0500
DMESW/COMAND,'FORMDEV/CIRCLE,NAME/F(圆度1),ELE-NAME/FA(圆8),UP-TOL/0.0500,UNIT/0,OUT-GRAPHIC/0'
OUTPUT/FA(圆8),TA(圆度1)
F(点7)=FEAT/POINT,CART,4.0000,0,-2.0000,0,-1.00000000,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_POINT_1007),AUTOFIGURE,F(点7),POINT,CART,DME,4.0000,0,-2.0000,0,-1.00000000,$
0,0,0,0,FALSE,FALSE,FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"","EXT1","EXT2",$
"EXT3",ENDCAL
F(点8)=FEAT/POINT,CART,32.0000,0,-2.0000,0,-1.00000000,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_POINT_1007),AUTOFIGURE,F(点8),POINT,CART,DME,32.0000,0,-2.0000,0,-1.00000000,$
0,0,0,0,FALSE,FALSE,FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"","EXT1","EXT2",$
"EXT3",ENDCAL
F(点9)=FEAT/POINT,CART,62.0000,0,-2.0000,0,-1.00000000,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_POINT_1007),AUTOFIGURE,F(点9),POINT,CART,DME,62.0000,0,-2.0000,0,-1.00000000,$
0,0,0,0,FALSE,FALSE,FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"","EXT1","EXT2",$
"EXT3",ENDCAL
F(点10)=FEAT/POINT,CART,0,4.0000,-2.0000,-1.00000000,0,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_POINT_1007),AUTOFIGURE,F(点10),POINT,CART,DME,0,4.0000,-2.0000,-1.00000000,$
0,0,0,0,0,FALSE,FALSE,FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"","EXT1","EXT2",$
"EXT3",ENDCAL
F(点11)=FEAT/POINT,CART,0,32.0000,-2.0000,-1.00000000,0,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_POINT_1007),AUTOFIGURE,F(点11),POINT,CART,DME,0,32.0000,-2.0000,-1.00000000,$
0,0,0,0,0,FALSE,FALSE,FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"","EXT1","EXT2",$
"EXT3",ENDCAL
F(点12)=FEAT/POINT,CART,0,58.0000,-2.0000,-1.00000000,0,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_POINT_1007),AUTOFIGURE,F(点12),POINT,CART,DME,0,58.0000,-2.0000,-1.00000000,$
0,0,0,0,0,FALSE,FALSE,FALSE,10.0000,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"","EXT1","EXT2",$
"EXT3",ENDCAL
DMESW/COMAND,'CONST/SET_PROJ_VEC,FA(XY),1'
F(直线4)=FEAT/LINE,UNBND,CART,4.0000,0,-2.0000,1.00000000,0,0,0,-1.00000000,0
CONST/LINE,F(直线4),BF,FA(点7),FA(点8),FA(点9)
DMESW/COMAND,'CONST/SET_PROJ_VEC,FA(XY),1'
F(直线5)=FEAT/LINE,UNBND,CART,0,4.0000,-2.0000,0,1.00000000,0,-1.00000000,0,0
CONST/LINE,F(直线5),BF,FA(点10),FA(点11),FA(点12)
T(角度1)=TOL/ANGLB,90.0000,-0.5000,0.5000,XYPLAN
DMESW/COMAND,'OUTPUT/UNIT,ANGLE/ANGDEC,TYPE/0'
OUTPUT/FA(直线4),FA(直线5),TA(角度1)


标签：NETDMIS5.0,FALSE,POINT,2023,CART,10.0000,FA,角度,1.00000000
From： https://blog.51cto.com/u_14941238/6165954

相关文章

  • 【一句日历】2023年4月
    【2023年4月1日·星期六】你是一树一树的开花，是燕在梁间呢喃，——你是爱，是暖，是希望，你是人间的四月天！                                                 ——林徽因【2023......
  • 【2023-03-31】打工圈子
    20:00要是一个人没有责任感，他能够心安理得吗？责任感使每件事变得神圣，并且把各种事情联系在一起，许多小责任构成一种大责任。                                                ......
  • 2023年五大团队任务管理软件盘点
    无论是作为企业还是个人，做好任务管理都能帮助我们很好实现项目或个人目标，但做好任务管理的前提，是要了解清楚什么是任务管理。任务管理的基本内容就是如何让一个部门或者岗位根据目标、计划形成在特定时间内最有效完成相关任务。以下任务管理软件将任务管理的基本内容结合到实际的......
  • 你到底值多少钱？2023打工人薪酬指南
    大家好，我是王有志，欢迎和我聊技术，聊漂泊在外的生活。作为打工人，你最关心什么？技能，成长，发展还是薪酬？刚毕业时，我为了赢得面试官的好感，说了很多违心话，如：“工资不要紧，主要是想学习”，又或者是“我对贵司的这块技术非常感兴趣”。现在想想，呸！恶心，哪怕是花钱嫖培训呢，也不要再傻乎乎的说......
  • 联合省选 2023 游记
    联合省选2023游记我OK冇事放松挠肚池把千斤重化做全部薄过纸——《尘大师》高二了，最后一次省选，好好打吧！关于一些外号解释：xzy：摇奖，hzr：蛤(酱)，txx：狗。Day-txx安利下大家开始玩他带来的桌游“炸弹猫咪”（我不知道这个要不要用书名号啊）。最后一个下午大家一起gar了......
  • 20230402-Python学习里程碑-day1
    Python基础-变量与数据类型4月2安装python注意：1、勾选ADDpythontopath（可以避免手动添加Path路径）2、选择安装路径（可以避免后续使用Pycharm时，配置解析器路径）安装Pycharm选择解析器：默认安装完后，创建一个工程项目，创建xxx.py文件，你会发现NoPythoninterpreterco......
  • 算法杂记 2023/04/02
    算法杂记2023/04/02目录算法杂记2023/04/02网易笔试第二题输入：输出：例子：6329.MakeK-SubarraySumsEqual网易笔试第二题给定一棵中序遍历的二叉树，如果当前树为空则表示为X，如果不为空则表示为(left_tree)cur_value(right_tree)，其中left_tree和right_tree分别表示按此规则序......
  • 2023-04-02 桥和割点以及图的遍历树
    桥和割点以及图的遍历树1什么是桥定义对于无向图，如果删除了一条边，整个图联通分量数量就会变化，则这条边称为桥(Bridge)。桥意味着图中最脆弱的关系应用交通系统比如两个城市上海和南京仅通过长江大桥相连，如果长江大桥被毁坏了，那么两个城市就分开各自为战了社交网络......
  • day33（2023.4.2）
    1.UDP传递基本数据类型(创建服务端)2.UDP传递基本数据类型(创建客户端) 运行结果: 3.UDP传递自定义对象类型   运行结果: 4.反射小概念 5.创建一个Users类  通过getClass()方法  运行结果: 6.通过.class静态属性获取Class对象和通过Class类中......
  • 2023.4.2
    #include<stdio.h>#include<string.h>////intAdd(intx,inty)//{// intz=0;// z=x+y;// returnz;//}//intmain()//{// inta=20;// intb=5;// intsum=Add(a,b);// printf("%d\n",sum);// return0;//}//intmai......

赞助商

阅读排行

网站主页关于我们联系我们网站地图

本网站内容转载自其他媒体，侵权联系[admin##ips99.com]。

Copyright © 2020-2023 IPS99 版权所有 IPS99