标签：reset 滤波器 end ast 带通 source std sink 幅频

1.软件版本

matlab2013b,quartusii121.

2.本算法理论知识

带通滤波器在数字幅频均衡功率放大器中一个重要的组成部分，在介绍带通滤波器之前，我们首先来详细介绍一下数字幅频均衡功率放大器。

本系统要求的指标为：

本题要求在输入电压有效值为5mV的条件下，放大倍数达到400倍。而且20Hz到20kHz衰减不能超过1dB。-1 dB转化为信号幅值变化为11%，可以说指标要求很高。我们可以选择使用PGA或AD620实现这一指标。

整个系统的基本结构如下所示：

根据以上分析，系统的整体框图如图1所示。输入信号首先通过前置放大电路放大到一定幅度，经过带阻网络后，信号的幅频特性发生变化。由于AD输入幅度限制，信号先经过衰减网络衰减两倍，再经过抗混叠滤波并使用AD对输入信号进行采样，将采样结果送入FPGA做幅频均衡。最后通过DA输出并滤波，经过D类功放后即可得到大功率信号。

·前置放大电路的设计

输入信号电压放大倍数不小于400倍，单级运放的放大倍数难以做到这么高，所以采用两级运放的形式来做前级放大。由于系统频率为20Hz~20kHz，所以选用OP27运放完成电路。

·抗混叠滤波器电路设计

根据采样定理，为了使采样信号不发生频域混叠，必须在A/D采样电路的前端加入抗混叠滤波器电路，滤波器截止频率为采样频率的一半。由于本系统主要处理20kHz以内的信号，所以选用开关电容滤波器LTC1068—25设计一个八阶椭圆滤波器，其截至频率为25kHz。

·A/D采样电路的设计

根据题目的指标及系统频率的要求，我们需要一款采样率超过40KHz的采样芯片。AD9223是一款12bits、最高采样频率10MHz的性能优良的AD采样器件，由于以前使用过该芯片，为了更快的完成题目，所以选用AD9223作为采样芯片。

·数字幅频均衡模块设计

数字幅频均衡模块的原理图如图4-3所示，如果要实现对带阻网络的完全补偿，那么FIR滤波器应与带阻网络互为逆系统.带阻网络的系统函数可以通过点频法测得，然后使用MATLAB求出加窗后FIR滤波器应该具有的单位脉冲响应。因为FIR系统具有线性相位特性，所以由其幅频响应就可以求得其系统函数。

·D/A输出电路设计

根据题目的指标及系统频率的要求，我们需要一款频率超过40KHz的模数输出芯片。DAC904是一款14bits、最高采样频率165MHz的的DA器件，由于以前使用过该芯片，所以仍选用DAC904作为数模输出芯片。

·功率放大电路设计

D类功放第一部分为调制器，输入信号接比较器的正输入端，与三角波相比较。当正端上的电位高于负端三角波电位时，比较器输出为高电平，反之则输出低电平。这样，比较器输出的波形就是一个脉冲宽度被音频信号幅度调制后的波形，称为SPWM波。D类功放后级输出电路是一个脉冲控制的大电流开关放大器，正半周期比较器输出高电平，MOSFET晶体管Q1导通，且Q2截止，负半周期比较器输出高电平Q2导通，且Q1截止，这样它就把比较器输出的PWM信号变成高电压、大电流的大功率PWM信号，最后只需要通过一个二阶低通滤波器就可以把声音信息还原出来。

3.部分源码

library ieee;
use ieee.std_logic_1164.all;
use ieee.numeric_std.all;
use std.textio.all;
entity tb_firs is
--START MEGAWIZARD INSERT CONSTANTS
constant FIR_INPUT_FILE_c : string := "firs_input.txt";
constant FIR_OUTPUT_FILE_c : string := "firs_output.txt";
constant NUM_OF_CHANNELS_c : natural := 1;
constant DATA_WIDTH_c : natural := 16;
constant CHANNEL_OUT_WIDTH_c : natural := 0;
constant OUT_WIDTH_c : natural := 35;
constant COEF_SET_ADDRESS_WIDTH_c : natural := 0;
constant COEF_RELOAD_BIT_WIDTH_c : natural := 35;

--END MEGAWIZARD INSERT CONSTANTS
end entity tb_firs;

--library work;
--library auk_dspip_lib;

-------------------------------------------------------------------------------

architecture rtl of tb_firs is

signal ast_sink_data : std_logic_vector (DATA_WIDTH_c-1 downto 0) := (others => '0');
signal ast_source_data : std_logic_vector (OUT_WIDTH_c-1 downto 0);
signal ast_sink_error : std_logic_vector (1 downto 0) := (others => '0');
signal ast_source_error : std_logic_vector (1 downto 0);
signal ast_sink_valid : std_logic := '0';
signal ast_source_valid : std_logic;
signal ast_source_ready : std_logic := '0';
signal clk : std_logic := '0';
signal reset_testbench : std_logic := '0';
signal reset_design : std_logic;
signal eof : std_logic;
signal ast_sink_ready : std_logic;
signal start : std_logic;
signal cnt : natural range 0 to NUM_OF_CHANNELS_c;
constant tclk : time := 10 ns;
constant time_lapse_max : time := 60 us;
signal time_lapse : time;
function div_ceil(a : natural; b : natural) return natural is
variable res : natural := a/b;
begin
if res*b /= a then
res := res +1;
end if;
return res;
end div_ceil;

function to_hex (value : in signed) return string is
constant ne : integer := (value'length+3)/4;
constant NUS : string(2 to 1) := (others => ' ');
variable pad : std_logic_vector(0 to (ne*4 - value'length) - 1);
variable ivalue : std_logic_vector(0 to ne*4 - 1);
variable result : string(1 to ne);
variable quad : std_logic_vector(0 to 3);
begin
if value'length < 1 then
return NUS;
else
if value (value'left) = 'Z' then
pad := (others => 'Z');
else
pad := (others => value(value'high));
end if;
ivalue := pad & std_logic_vector (value);
for i in 0 to ne-1 loop
quad := To_X01Z(ivalue(4*i to 4*i+3));
case quad is
when x"0" => result(i+1) := '0';
when x"1" => result(i+1) := '1';
when x"2" => result(i+1) := '2';
when x"3" => result(i+1) := '3';
when x"4" => result(i+1) := '4';
when x"5" => result(i+1) := '5';
when x"6" => result(i+1) := '6';
when x"7" => result(i+1) := '7';
when x"8" => result(i+1) := '8';
when x"9" => result(i+1) := '9';
when x"A" => result(i+1) := 'A';
when x"B" => result(i+1) := 'B';
when x"C" => result(i+1) := 'C';
when x"D" => result(i+1) := 'D';
when x"E" => result(i+1) := 'E';
when x"F" => result(i+1) := 'F';
when "ZZZZ" => result(i+1) := 'Z';
when others => result(i+1) := 'X';
end case;
end loop;
return result;
end if;
end function to_hex;
begin

DUT : entity work.firs
port map (
clk => clk,
reset_n => reset_design,
ast_sink_ready => ast_sink_ready,
ast_sink_data => ast_sink_data,
ast_source_data => ast_source_data,
ast_sink_valid => ast_sink_valid,
ast_source_valid => ast_source_valid,
ast_source_ready => ast_source_ready,
ast_sink_error => ast_sink_error,
ast_source_error => ast_source_error);
-- for example purposes, the ready signal is always asserted.
ast_source_ready <= '1';

-- no input error
ast_sink_error <= (others => '0');

-- start valid for first cycle to indicate that the file reading should start.
start_p : process (clk, reset_testbench)
begin
if reset_testbench = '0' then
start <= '1';
elsif rising_edge(clk) then
if ast_sink_valid = '1' and ast_sink_ready = '1' then
start <= '0';
end if;
end if;
end process start_p;
-----------------------------------------------------------------------------------------------
-- Read input data from file
-----------------------------------------------------------------------------------------------
source_model : process(clk) is
file in_file : text open read_mode is FIR_INPUT_FILE_c;
variable data_in : integer;
variable indata : line;
begin
if rising_edge(clk) then
if(reset_testbench = '0') then
ast_sink_data <= std_logic_vector(to_signed(0, DATA_WIDTH_c)) after tclk/4;
ast_sink_valid <= '0' after tclk/4;
eof <= '0';
else
if not endfile(in_file) and (eof = '0') then
eof <= '0';
if((ast_sink_valid = '1' and ast_sink_ready = '1') or
(start = '1'and not (ast_sink_valid = '1' and ast_sink_ready = '0'))) then
readline(in_file, indata);
read(indata, data_in);
ast_sink_valid <= '1' after tclk/4;
ast_sink_data <= std_logic_vector(to_signed(data_in, DATA_WIDTH_c)) after tclk/4;
else
ast_sink_valid <= '1' after tclk/4;
ast_sink_data <= ast_sink_data after tclk/4;
end if;
else
eof <= '1';
ast_sink_valid <= '0' after tclk/4;
ast_sink_data <= std_logic_vector(to_signed(0, DATA_WIDTH_c)) after tclk/4;
end if;
end if;
end if;
end process source_model;
---------------------------------------------------------------------------------------------
-- Write FIR output to file
---------------------------------------------------------------------------------------------

sink_model : process(clk) is
file ro_file : text open write_mode is FIR_OUTPUT_FILE_c;
variable rdata : line;
variable data_r : string(div_ceil(OUT_WIDTH_c,4) downto 1);
begin
if rising_edge(clk) then
if(ast_source_valid = '1' and ast_source_ready = '1') then
-- report as hex representation of integer.
data_r := to_hex(signed(ast_source_data));
write(rdata, data_r);
writeline(ro_file, rdata);
end if;
end if;
end process sink_model;
-------------------------------------------------------------------------------
-- clock generator
-------------------------------------------------------------------------------
clkgen : process
begin -- process clkgen
if eof = '1' then
clk <= '0';
assert FALSE
report "NOTE: Stimuli ended" severity note;
wait;
elsif time_lapse >= time_lapse_max then
clk <= '0';
assert FALSE
report "ERROR: Reached time_lapse_max without activity, probably simulation is stuck!" severity Error;
wait;
else
clk <= '0';
wait for tclk/2;
clk <= '1';
wait for tclk/2;
end if;
end process clkgen;

monitor_toggling_activity : process(clk, reset_testbench,
ast_source_data, ast_source_valid)
begin
if reset_testbench = '0' then
time_lapse <= 0 ns;
elsif ast_source_data'event or ast_source_valid'event then
time_lapse <= 0 ns;
elsif rising_edge(clk) then
if time_lapse < time_lapse_max then
time_lapse <= time_lapse + tclk;
end if;
end if;
end process monitor_toggling_activity;

-------------------------------------------------------------------------------
-- reset generator
-------------------------------------------------------------------------------
reset_testbench_gen : process
begin -- process resetgen
reset_testbench <= '1';
wait for tclk/4;
reset_testbench <= '0';
wait for tclk*2;
reset_testbench <= '1';
wait;
end process reset_testbench_gen;
reset_design_gen : process
begin -- process resetgen
reset_design <= '1';
wait for tclk/4;
reset_design <= '0';
wait for tclk*2;
reset_design <= '1';
wait for tclk*80;
reset_design <= '1';
wait for tclk*128*2;
reset_design <= '1';
wait;
end process reset_design_gen;

-------------------------------------------------------------------------------
-- control signals
-------------------------------------------------------------------------------

end architecture rtl;