首页 > 其他分享 >华为Datacom 综合拓扑案例—分享篇

华为Datacom 综合拓扑案例—分享篇

时间:2023-08-14 17:32:37浏览次数:42  
标签:Datacom LSW4 LSW5 int 0.0 拓扑 GigabitEthernet0 华为 ip

拓扑图

华为Datacom 综合拓扑案例—分享篇_链路

题目要求

实验要求:

1、PC1\PC2\PC3\PC4采用DHCP自动获取IP地址,SW5作为服务器,SW3和SW4作为中继

创建地址池ip pool huawei1和ip pool huawei2,租期都为2天

2、SW3与SW4做链路聚合,采用LACP模式。SW3作为主交换机,优先级为0

抢占延时时间为10秒

让G0/0/4接口成为非活跃链路,优先级为65000

3、在SW3\SW4\SW5构成的环形链路中,让SW5为主交换机,优先级为4096

4、在AR1位置做地址转换,采用NAPT方式,地址池范围200.1.1.10-200.1.1.20

client访问内网服务器server1时,采用NAT server,用公网ip200.1.1.100替代10.1.3.1

实现client可以ping通200.1.1.100

5、配置全网,实现内网PC可以访问外网client202.1.1.1

解析

LSW1:

[Huawei]sy LSW1
[LSW1]v b 10
[LSW1]int e0/0/1
[LSW1-Ethernet0/0/1]port link-t a
[LSW1-Ethernet0/0/1]po de v 10
[LSW1-Ethernet0/0/1]int e0/0/2
[LSW1-Ethernet0/0/2]port link-t a
[LSW1-Ethernet0/0/2]po de v 10
[LSW1-Ethernet0/0/2]int e0/0/3
[LSW1-Ethernet0/0/3]port link-t t
[LSW1-Ethernet0/0/3]po t a v 101.2.3.4.5.6.7.8.9.10.11.

LSW2:

[LSW2]v b 20
[LSW2]int e0/0/1
[LSW2-Ethernet0/0/1]po link-t a
[LSW2-Ethernet0/0/1]po de v 20
[LSW2-Ethernet0/0/1]int e0/0/2
[LSW2-Ethernet0/0/2]po link-t a
[LSW2-Ethernet0/0/2]po de v 20
[LSW2-Ethernet0/0/2]int e0/0/3
[LSW2-Ethernet0/0/3]po link-t t
[LSW2-Ethernet0/0/3]po t a v 201.2.3.4.5.6.7.8.9.10.

LSW3:

[LSW3]int et 1
[LSW3-Eth-Trunk1]mode lacp-static   
[LSW3-Eth-Trunk1]trunkport g0/0/3
[LSW3-Eth-Trunk1]trunkport g0/0/4
[LSW3-Eth-Trunk1]trunkport g0/0/5
[LSW3-Eth-Trunk1]q  
[LSW3]lacp priority 0
[LSW3]int et 1
[LSW3-Eth-Trunk1]lacp preempt enable 
[LSW3-Eth-Trunk1]lacp preempt delay 10  
[LSW3-Eth-Trunk1]max active-linknumber 2
[LSW3-GigabitEthernet0/0/3]int g0/0/4
[LSW3-GigabitEthernet0/0/4]lacp priority 65000   
[LSW3-GigabitEthernet0/0/4]int et 1 
[LSW3-Eth-Trunk1]port link-type t
[LSW3-Eth-Trunk1]po t a v 34
[LSW3-Eth-Trunk1]int v 34
[LSW3-Vlanif34]ip ad 34.1.1.3 24


[LSW3]stp mode stp
[LSW3]ip route-static 0.0.0.0 0 30.1.1.51.2.3.4.5.6.7.8.9.10.11.12.13.14.15.16.17.18.19.20.21.22.

LSW4:

[LSW4]v b 20 34 40
[LSW4]int g0/0/1
[LSW4-GigabitEthernet0/0/1]po link-t t
[LSW4-GigabitEthernet0/0/1]po t a v 20
[LSW4-GigabitEthernet0/0/1]int g0/0/2
[LSW4-GigabitEthernet0/0/2]po link-t t
[LSW4-GigabitEthernet0/0/2]po t a v 40
[LSW4-GigabitEthernet0/0/2]q  
[LSW4]dhcp enable 
[LSW4]dhcp server group bosai2
[LSW4-dhcp-server-group-bosai2]dhcp-server 40.1.1.5
[LSW4-dhcp-server-group-bosai2]int vlan 40
[LSW4-Vlanif40]ip ad 40.1.1.4 24
[LSW4-Vlanif40]int vlan 20
[LSW4-Vlanif20]ip ad 10.1.2.254 24  
[LSW4-Vlanif20]dhcp select relay 
[LSW4-Vlanif20]dhcp relay server-select bosai2
[LSW4-Vlanif20]q  
[LSW4]ospf router-id 4.4.4.4
[LSW4-ospf-1]a 1
[LSW4-ospf-1-area-0.0.0.1]net 10.1.2.0 0.0.0.255
[LSW4-ospf-1-area-0.0.0.1]net 40.1.1.0 0.0.0.255
[LSW4-ospf-1-area-0.0.0.1]net 34.1.1.0 0.0.0.255
[LSW4-ospf-1-area-0.0.0.1]int et 1
[LSW4-Eth-Trunk1]mode lacp-static   
[LSW4-Eth-Trunk1]trunkport g0/0/3
[LSW4-Eth-Trunk1]trunkport g0/0/4
[LSW4-Eth-Trunk1]trunkport g0/0/5
[LSW4-Eth-Trunk1]lacp preempt enable  
[LSW4-Eth-Trunk1]lacp preempt delay 10
[LSW4-Eth-Trunk1]max active-linknumber 2
[LSW4-Eth-Trunk1]q
[LSW4]int et 1
[LSW4-Eth-Trunk1]po link-t t
[LSW4-Eth-Trunk1]po t a v 34
[LSW4-Eth-Trunk1]int vlan 34
[LSW4-Vlanif34]ip ad 34.1.1.4 24

[LSW4]stp mode stp
[LSW4]ip route-static 0.0.0.0 0 40.1.1.51.2.3.4.5.6.7.8.9.10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.26.27.28.29.30.31.32.33.34.35.36.37.38.39.40.

LSW5:

[LSW5]int g0/0/1
[LSW5-GigabitEthernet0/0/1]po link-t t
[LSW5-GigabitEthernet0/0/1]po t a v 30
[LSW5-GigabitEthernet0/0/1]int g0/0/2
[LSW5-GigabitEthernet0/0/2]po link-t t
[LSW5-GigabitEthernet0/0/2]po t a v 40
[LSW5]v b 30 40 15
[LSW5]int g0/0/3
[LSW5-GigabitEthernet0/0/3]po link-t a
[LSW5-GigabitEthernet0/0/3]po de v 15
[LSW5-GigabitEthernet0/0/3]q
[LSW5]dhcp enable 
[LSW5]ip pool huawei1 
[LSW5-ip-pool-huawei1]gateway-list 10.1.1.254   
[LSW5-ip-pool-huawei1]network 10.1.1.0 mask 24
[LSW5-ip-pool-huawei1]int vlan 30
[LSW5-Vlanif30]ip ad 30.1.1.5 24  
[LSW5-Vlanif30]dhcp select global 
[LSW5-Vlanif30]q  
[LSW5]ospf router-id 5.5.5.5
[LSW5-ospf-1]a 1
[LSW5-ospf-1-area-0.0.0.1]net 30.1.1.0 0.0.0.255
[LSW5-ospf-1-area-0.0.0.1]net 15.1.1.0 0.0.0.255
[LSW5-ospf-1-area-0.0.0.1]q
[LSW5-ospf-1]q
[LSW5]ip route-static 10.1.1.0 24 30.1.1.3
[LSW5]ip pool huawei2 
[LSW5-ip-pool-huawei2]gateway-list 10.1.2.254 
[LSW5-ip-pool-huawei2]network 10.1.2.0 mask 24
[LSW5-ip-pool-huawei2]int vlan 40
[LSW5-Vlanif40]ip ad 40.1.1.5 24  
[LSW5-Vlanif40]dhcp select global 
[LSW5-Vlanif40]q  
[LSW5]ip route-static 10.1.2.0 24 40.1.1.4
[LSW5]ip pool huawei1
[LSW5-ip-pool-huawei1]lease day 2
[LSW5-ip-pool-huawei1]q
[LSW5]ip pool huawei2 
[LSW5-ip-pool-huawei2]lease day 2
[LSW5-ip-pool-huawei2]int vlan 15
[LSW5-Vlanif15]ip ad 15.1.1.5 24
[LSW5-Vlanif15]ospf ro 5.5.5.5
[LSW5-ospf-1]a 1
[LSW5-ospf-1-area-0.0.0.1]net 40.1.1.0 0.0.0.255


[LSW5]stp mode stp
[LSW5]stp priority 4096
[LSW5]ip route-static 0.0.0.0 0 15.1.1.11.2.3.4.5.6.7.8.9.10.11.12.13.14.15.16.17.18.19.20.21.22.23.24.25.26.27.28.29.30.31.32.33.34.35.36.37.38.39.40.41.42.43.44.45.46.47.48.49.

R1:

[R1]int g0/0/0
[R1-GigabitEthernet0/0/0]ip ad 15.1.1.1 24
[R1-GigabitEthernet0/0/0]int g0/0/1
[R1-GigabitEthernet0/0/1]ip ad 12.1.1.1 24
[R1-GigabitEthernet0/0/1]int g0/0/2
[R1-GigabitEthernet0/0/2]ip ad 10.1.3.254 24
[R1-GigabitEthernet0/0/2]q
[R1]ospf router-id  11.1.1.1
[R1-ospf-1]a 1
[R1-ospf-1-area-0.0.0.1]net 12.1.1.0 0.0.0.255
[R1-ospf-1-area-0.0.0.1]net 10.1.3.0 0.0.0.255
[R1-ospf-1-area-0.0.0.1]net 15.1.1.0 0.0.0.255
[R1]ip route-static 0.0.0.0 0 12.1.1.21.2.3.4.5.6.7.8.9.10.11.12.13.

R2:

[R2]int g0/0/0
[R2-GigabitEthernet0/0/0]ip ad 12.1.1.2 24
[R2-GigabitEthernet0/0/0]int g0/0/1
[R2-GigabitEthernet0/0/1]ip ad 23.1.1.2 24
[R2-GigabitEthernet0/0/1]int g0/0/2
[R2-GigabitEthernet0/0/2]ip ad 24.1.1.2 24
[R2-GigabitEthernet0/0/2]q
[R2]ospf ro 22.1.1.1
[R2-ospf-1]a 1
[R2-ospf-1-area-0.0.0.1]net 12.1.1.0 0.0.0.255
[R2-ospf-1-area-0.0.0.1]q
[R2-ospf-1]a 0
[R2-ospf-1-area-0.0.0.0]net 23.1.1.0 0.0.0.255
[R2-ospf-1-area-0.0.0.0]net 24.1.1.0 0.0.0.255
  
[R2]ip route-static 0.0.0.0 0 23.1.1.3
[R2]ip route-static 0.0.0.0 0 24.1.1.41.2.3.4.5.6.7.8.9.10.11.12.13.14.15.16.17.

R3:

[R3]int g0/0/0
[R3-GigabitEthernet0/0/0]ip ad 23.1.1.3 24
[R3-GigabitEthernet0/0/0]int g0/0/1
[R3-GigabitEthernet0/0/1]ip ad 35.1.1.3 24
[R3-GigabitEthernet0/0/1]q
[R3]ospf ro 33.1.1.1 
[R3-ospf-1]a 0
[R3-ospf-1-area-0.0.0.0]net 23.1.1.0 0.0.0.255
[R3-ospf-1-area-0.0.0.0]net 35.1.1.0 0.0.0.255

  
[R3]ip route-static 0.0.0.0 0 35.1.1.51.2.3.4.5.6.7.8.9.10.11.12.

R4:

[R4]int g0/0/0
[R4-GigabitEthernet0/0/0]ip ad 24.1.1.4 24
[R4-GigabitEthernet0/0/0]int g0/0/1
[R4-GigabitEthernet0/0/1]ip ad 45.1.1.4 24
[R4-GigabitEthernet0/0/1]q
[R4]ospf ro 44.1.1.1
[R4-ospf-1]a 0
[R4-ospf-1-area-0.0.0.0]net 24.1.1.0 0.0.0.255
[R4-ospf-1-area-0.0.0.0]net 45.1.1.0 0.0.0.255

  
[R4]ip route-static 0.0.0.0 0 45.1.1.51.2.3.4.5.6.7.8.9.10.11.12.

R5:

[R5]ip route-static 0.0.0.0 0 51.1.1.11.

LSW6:

[LSW6]int e0/0/1
[LSW6-Ethernet0/0/1]q
[LSW6]v b 50 60
[LSW6]int e0/0/1
[LSW6-Ethernet0/0/1]po link-t t
[LSW6-Ethernet0/0/1]po t a v 50 60
[LSW6-Ethernet0/0/1]int e0/0/2
[LSW6-Ethernet0/0/2]po link-t a
[LSW6-Ethernet0/0/2]po de v 50
[LSW6-Ethernet0/0/2]int e0/0/3
[LSW6-Ethernet0/0/3]po link-t a
[LSW6-Ethernet0/0/3]po de v 601.2.3.4.5.6.7.8.9.10.11.12.
[AR1-acl-basic-2000]rule  permit source 10.1.1.0 0.0.0.255
[AR1-acl-basic-2000]rule permit source 10.1.2.0 0.0.0.255
[AR1-acl-basic-2000]rule permit source 10.1.3.0 0.0.0.255 
[AR1-acl-basic-2000]rule permit source 60.1.1.0 0.0.0.255
[AR1-acl-basic-2000]rule permit source 50.1.1.0 0.0.0.255
[AR1-acl-basic-2000]q
[AR1]nat address-group 1 200.1.1.10 200.1.1.20
[AR1]int g0/0/1 
[AR1-GigabitEthernet0/0/1]nat outbound 2000 address-group 1
[AR1-GigabitEthernet0/0/1]nat server global 200.1.1.100 inside 10.1.3.11.2.3.4.5.6.7.8.9.10.
AR2:
[AR2]int g0/0/0
[AR2-GigabitEthernet0/0/0]ip ad 200.1.1.2 24
[AR2-GigabitEthernet0/0/0]int g0/0/1
[AR2-GigabitEthernet0/0/1]ip ad 202.1.1.254 241.2.3.4.5.

华为Datacom 综合拓扑案例—分享篇_链路_02

华为Datacom 综合拓扑案例—分享篇_优先级_03

华为Datacom 综合拓扑案例—分享篇_链路_04

华为Datacom 综合拓扑案例—分享篇_R3_05

转载:https://blog.51cto.com/u_15964895/6839898

标签:Datacom,LSW4,LSW5,int,0.0,拓扑,GigabitEthernet0,华为,ip
From: https://blog.51cto.com/atomguo/7079458

相关文章

  • [YsOI2023] 广度优先遍历 逆向输出路径(分层建树拓扑序. LCA)
    今天的模板测试是无向图上的广度优先遍历,【数据删除】马上写好了代码:1#include<cstdio>2#include<cstring>3#include<iostream>4#include<algorithm>5#include<vector>6#include<queue>7usingnamespacestd;8constintmaxn=100005;......
  • 华为数通方向HCIP-DataCom H12-821题库(单选题:81-100)
    第81题某公司新购入一台网络设备,作为网络管理员,初次配置该设备通常通过什么方式?A、FTPB、TelnetC、SNMPD、Console口登录答案:D解析:通常情况下,初次配置网络设备会通过Console口登录的方式进行。Console口是一种串口接口,可以直接连接到设备的控制台端口。通过Console口登录设备......
  • 华为OD机试-位运算
     importjava.util.ArrayList;publicclassMain{publicstaticvoidmain(String[]args){Integer[]nums=newInteger[]{3,5,2,8,4};//差异值---》异或运算^//相似值---》与运算&ArrayList<Integer[]>pairs=n......
  • 华为OD机试-公司分奖金
      importjava.util.Arrays;importjava.util.Objects;importjava.util.stream.Collectors;publicclassMain{publicstaticvoidmain(String[]args){Integer[]emp=newInteger[]{2,10,3};Integer[]scholar=newInteger[emp.len......
  • 华为OD机试-区间叠加
       importjava.util.ArrayList;importjava.util.TreeMap;importjava.util.stream.IntStream;publicclassMain{publicstaticvoidmain(String[]args){Integer[][]lines=newInteger[5][2];lines[0]=newInteger[]{1,4};......
  • 华为OD机试-热点网站统计
        importjava.util.*;importjava.util.stream.Collectors;publicclassMain{publicstaticvoidmain(String[]args){String[]urls={"news.qq.com","news.sina.com.cn","news.qq.com","news.qq.co......
  • 华为OD机试-路灯照明问题
      importjava.util.stream.IntStream;publicclassMain{publicstaticvoidmain(String[]args){int[]lights=newint[]{50,70,20,70};inttotal=IntStream.range(0,lights.length-1).map(idx->100-lights[idx]-lights......
  • blender 拓扑
    原理https://topologyguides.com/loop-reductionhttps://www.bilibili.com/video/BV1Fj411K7eL使用插件RetopoFlow3加速拓扑流程:https://www.youtube.com/watch?v=9OjS2rU-Jr0人脸按住C微调Ctrl+Shift+左键后按F确认填充主要循环边→细化......
  • 华为策略路由
    1、配置ACL规则acl3000rulepermitipsource192.168.1.00.0.0.2552、配置流分类trafficclassifierc1operatorandif-matchacl30003、配置流行为trafficbehaviorb1redirectip-nexthop192.168.2.24、配置流策略trafficpolicyp1classifierc1......
  • 揭秘华为云GaussDB(for Redis)丨大key治理
    本文分享自华为云社区《华为云GaussDB(forRedis)揭秘第31期:大key治理》,作者:高斯Redis官方博客。从DBA的视角看,大Key无疑是引起Redis线上问题的常见原因。为了解决大Key隐患,业务首先要遵守合理的开发规范,减少大Key的产生和访问依赖。但有时大Key是在程序运行过程中悄悄产生的,让......